Nov 21, 2011 · I'm new to Arch Linux and I just installed it, but I want to give it a try. For some reason, I can't connect to the internet. "ping" fails, but "ifconfig -a" does return with "eth0"
25.11.2018 · Re: Can't connect via ethernet after update Yeah, like I said, you can opt for 1.1.1.1 or 8.8.8.8 instead, that is if it's reachable. No idea why it would be refusing queries.
27.11.2018 · Posts: 34. Re: Can't connect via ethernet after update. bugsmanagement wrote: You should have remove the ones that don't work, you'll end up with intermittent DNS lookup failures otherwise. nameserver 1.1.1.1 nameserver 1.0.0.1 nameserver 8.8.8.8. Removed them and added those, and still no luck. Offline.
Connecting to the Internet. After booting into the Arch Linux ISO, there are 3 ways you can get online: Via wifi; Via ethernet; Via Android tethering ...
Apr 17, 2020 · I installed arch linux and while doing it everything was great and awesome. I could connect to the internet and download whatever package I wanted. But after installing and rebooting I didn't have any package e.g. wifi-menu, dhcpcd, iw and netctl, so I can't connect to the internet.
01.12.2021 · from ethernet or phone thether or another computer if must be on reproduction. Offline #3 2021-12-01 06:21:46. malta Member Registered: 2017-10-08 Posts: 20. Re: [SOLVED] Can't connect to wifi. found a "solution": disabling ipv6 fix it. after reading this I realised arch linux can't setup ipv6 for some unknown reason. Now everything ...
On the hardware acceleration Arch Wiki page check if your GPU and hardware acceleration driver can decode VP9 if it can't install the h264ify browser extension otherwise you wont be able to watch stuff like YouTube videos with hardware video decoding keep in mind h264ify will disable resolutions above 1080p here is the Arch Wiki link: https ...
Jan 10, 2019 · I am trying to install arch-linux on my thinkpad following the installation wiki. I plugged in the ethernet cable, and the ip link command will show: enp8s0: <BROADCAST,MULTICAST,UP,LOWER_UP>...
Feb 24, 2018 · Hey guys, So I update my Arch system just about every day, and yesterday's update messed up my ethernet connection. A LOT of packages were updated, so I'm not sure which is the culprit. Here's the outputs of commands that seemed relevant after reading the wiki and Google searching: [david@archPC ~]$ ip link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu ...
Feb 13, 2016 · ip route didn't return anything. EDIT: Wierd, after plugging in a lan cable, while the usb drive was connected the usb drive is able to connect to the internet, even after the lan cable was unplugged. But that only works until I restart (And I couldn't reproduce it) Last edited by universal (2016-02-13 13:32:09)
ifplugd is a daemon which will automatically configure your Ethernet device when a cable is plugged in and automatically unconfigure it if the cable is pulled. This is useful on laptops with onboard network adapters, since it will only configure the interface when a cable is really connected. Another use is when you just need to restart the network but do not want to restart …
Plug in the Ethernet cable or connect to the wireless LAN. Configure your network connection: static IP address. dynamic IP address: use DHCP. Note: The installation image uses systemd-resolved and systemd-networkd, which is configured as a DHCP client for Ethernet, WLAN and WWAN network interfaces.
09.01.2019 · I am trying to install arch-linux on my thinkpad following the installation wiki. I plugged in the ethernet cable, and the ip link command will show: enp8s0: <BROADCAST,MULTICAST,UP,LOWER_UP>...
22.08.2016 · I'm having a problem with connecting to my university's internet via ethernet. I had to register my device with it's MAC address and it assigned an IP address to me (10.41.72.65). However, when I use dhcpcd to set up my connection, I can't ping/connect to any sites or IP addresses besides internal ones as it just drops all the packets.