The interface (FastEthernet0/6) on S0 was not configured as switchport in access mode for Vlan 17, so there was no connectivity between both switches. The port ...
Apr 23, 2018 · I'm a student at a college and I keep getting issues in doing the ping and it always tell me that the destination host is unreachable. I would to get some help on what's wrong with the configuration. I used 255.255.255.0 for the mask, and for the hub I used 10.1.1.1 Regards, Sara
04.03.2021 · Solved: Hello! I'm currently on a small case study using packet tracer and sadly I'm already having troubles. The problem is that when I ping the Server using the PC's from all the networks, it says "destination host unreachable" but every
Mar 23, 2017 · Destination Host Unreachable So I've set up a small lab in GNS3, and I don't know why I can't ping to my default gateway as I've seem to keep getting destination host unreachable. I've narrowed down the problem to the switch I'm using, because without the switch I know I can ping the default gateway just fine.
31.12.2019 · Destination Host Unreachable. Hi, I am trying to ping the server from PC3 and PC4 only (green highlighted) however, I keep getting destination host unreachable. I am not sure what's incorrect. Please advise - I have attached the packet tracer file within the zip folder as it does not allow me to attach the .pkt file.
15.03.2021 · 03-15-2021 06:06 AM. Hello @drenzasludi38493. ICMP "Destination host unreachable" means the router/layer3 device doesn't have a route to the destination. Please verify the routing table of the router/Layer3 device sending "Destination host unreachable". ***Please rate all helpful posts***. Sr Network Engineer.
‘Destination Host Unreachable’ is one of the usual but unexpected errors that flow out while carrying a network ping test. It is a type of Troubleshooting IP Default Gateway Issues that induce incorrect default gateway, which further leads to halt in a network ping test.
18.09.2015 · Destination host unreachable is generated by 3750X which is a default gateway of PC A. Here is a question. If I get only destination host unreachable or only request timed out, then it make sense. ... if yes try debug ip detail on cisco 3750 switch and see what happen when you give icmp response from PC A to PC B.
Normally By default, the input interface sends ICMP Unreachable messages whenever a packet is discarded, regardless of whether the packet was discarded because ...
I have trunked both router cable to the switch. I have set 1 ip table per router which correspond to the ip address of the PC that have this router address as a gateway. When I ping from 192.168.100.2 to 192.168.200.2 it tells me that destination host is unreachable and the message is from the router 192.168.100.1.
... Hi everyone: I have a school project and when I ping computer PC-A to PC-C and vice versa, I get Destination host Unreachable. ... Labels: LAN Switching.
Hi, my name is Edwin I'm a student and I'm working on the this assignment and I'm having trouble with it I trying to ping PC5 from PC0, but it keep saying Destination Host Unreachable.
Dec 31, 2019 · Destination Host Unreachable. Hi, I am trying to ping the server from PC3 and PC4 only (green highlighted) however, I keep getting destination host unreachable. I am not sure what's incorrect. Please advise - I have attached the packet tracer file within the zip folder as it does not allow me to attach the .pkt file.
22.01.2019 · Routers must have marked routes to the networks you want to visit. These networks can be configured statically or learned by routing protocols, such as RIPv2. To configure RIP v2 on your routers do this: R1 (config)#router rip. R1 (config-router)#network 10.1.1.0. R1 (config-router)#network 192.168.1.0.
Jan 22, 2019 · Routers must have marked routes to the networks you want to visit. These networks can be configured statically or learned by routing protocols, such as RIPv2. To configure RIP v2 on your routers do this: R1 (config)#router rip. R1 (config-router)#network 10.1.1.0. R1 (config-router)#network 192.168.1.0.