27.12.2021 · DD-WRT does offer different kinds of IPv6 handling: Native IPv6 from ISP DHCPv6 with Prefix Delegation 6in4 Static Tunnel Here is a bunch of IPv6 wiki pages, ... Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one. Atheros: Netgear R7800 - WDS AP, gateway, QoS
“Native” IPv6 is provided by ISPs using a protocol called DHCPv6-PD (Prefix Delegation). This requires that your router sends a DHCPv6 request to the ISP to ask for a prefix, then uses the prefix that it received to give out addresses to the computers on your lan.
21.09.2018 · The first thing we need to do is to enable IPv6 in the DD-WRT web interface. Configure the basic IPv4 setup as usual, make sure it's working with your ISP, then go to Setup => IPv6. In there, you'll need to enable IPv6 and specify …
May 24, 2021 · Posted: Mon May 24, 2021 14:08 Post subject: IPV6 server using Native IPV6 from ISP config [help]: Hi everyone, I've been trying to make IPV6 DHCP work using the Native IPV6 from my ISP as this is the only way the router gets an IPV6 address.
30.06.2017 · DD-WRT Forum Forum Index-> Broadcom SoC based Hardware: View previous topic:: View next topic . Author Message; Clementtang DD-WRT Novice Joined: 13 Dec 2014 Posts: 1: Posted: Sat Dec 13, 2014 13:11 Post subject: IPv6 on LAN With Native IPv6 from ISP ...
01.11.2015 · As I mentioned in a previous post, I installed dd-wrt (kernel 2.6, VOIP, build 14896) on my wireless router (Linksys WRT320N), which connected to a VDSL modem using PPPoE.After that, it worked fine for IPv4, so I had the same functionality as the original Linksys firmware. However, the purpose of the exercise was to get IPv6 support: this turned out to be easier said …
Nov 01, 2015 · So, here’s a quick recap on the relevant steps. If you have a WRT320N router, and you want to use dd-wrt to get native IPv6 internet access over PPPoE, here’s what you need to do: Make a note of all your current settings. Reset the Linksys firmware to factory settings. Install the trailed build (14471, mini). Do a hard reset.
“Native” IPv6 is provided by ISPs using a protocol called DHCPv6-PD (Prefix Delegation). This requires that your router sends a DHCPv6 request to the ISP to ask for a prefix, then uses the prefix that it received to give out addresses to the computers on your lan.
Dec 25, 2021 · DD-WRT does offer different kinds of IPv6 handling: Native IPv6 from ISP DHCPv6 with Prefix Delegation ... Some dd-wrt wiki pages are up to date, others are not. PM ...
realcapone. DD-WRT Novice Joined: 24 May 2021. Posts: 6. Post Posted: Mon May 24, 2021 14:08 Post subject: IPV6 server using Native IPV6 from ISP config ...
27.10.2017 · Posted: Thu Oct 26, 2017 9:00 Post subject: PPPoE Native IPv6 from ISP assign IP to LAN problem: Hi,everyone,Sorry for my English. I'm in Hunan,China,The ISP set a fiber optic modem at bridge mode in my House ,So I use Netgear R7000 and DD-WRT v3.0-r33607 to dial up,by use PPPoE.
Sep 21, 2018 · The first thing we need to do is to enable IPv6 in the DD-WRT web interface. Configure the basic IPv4 setup as usual, make sure it's working with your ISP, then go to Setup => IPv6. In there, you'll need to enable IPv6 and specify the type of IPv6 autoconfiguration your ISP uses.