Oct 11, 2002 · virtual interface eth0:0 Linux - General This Linux forum is for general Linux questions and discussion. If it is Linux Related and doesn't seem to fit in any other forum then this is the place. Notices Welcome to LinuxQuestions.org, a friendly and active Linux Community. You are currently viewing LQ as a guest.
Oct 15, 2021 · $ sudo ip addr add 192.168.1.100/24 brd + dev eth0 label eth0:0 Don’t forget to put the interface up, or it probably won’t be very useful. $ sudo ip link set dev eth0 up You should now be able to use your virtual network interface for whatever you want. You can see the full configuration by viewing the output of the ip a command.
eth0 is the first ethernet interface, any additional ethernet interfaces would be named eth1, eth2, etc. Share Improve this answer answered Feb 9 '17 at 12:56 Toby.S 51 1 1 Add a comment Highly active question. Earn 10 reputation (not counting the association bonus) in order to answer this question.
Jun 17, 2006 · To create alias for eth0 use ifconfig command. It is use to configure a network interface and aliases. Assuming that your eth0 IP is 192.168.1.10 and you would like to create an alias eth0:0 with IP 192.168.1.11. Type the following command: sudo ifconfig eth0:0 192.168.1.11 up. OR.
It seems that eth0:0 gets to be the one each time, so by hardcoding GATEWAYDEV="eth0" you make sure that eth0 is always selected as the gateway device. In older versions of RH you could just edit /etc/sysconfig/static-routes and add default via 5.x.y.82 dev eth0 As a last resort /etc/rc.local is always your friend! Share Improve this answer
It examines the route to the gateway IP with ip get route to GATEWAY and, using sed, matches the a device. It seems that eth0:0 gets to be the one each time, so ...
17.06.2006 · A. To create alias for eth0 use ifconfig command. It is use to configure a network interface and aliases. Assuming that your eth0 IP is 192.168.1.10 and you would like to create an alias eth0:0 with IP 192.168.1.11.
15.10.2021 · $ sudo ip addr add 192.168.1.100/24 brd + dev eth0 label eth0:0 Don’t forget to put the interface up, or it probably won’t be very useful. $ sudo ip link set dev eth0 up You should now be able to use your virtual network interface for whatever you want. You can see the full configuration by viewing the output of the ip a command.
12.08.2021 · Using the “ ifconfig ” command with the “ netmask ” argument and interface name as ( eth0) allows you to define a netmask to a given interface. For example, “ ifconfig eth0 netmask 255.255.255.224 ” will set the network mask to a given interface eth0. [ root@tecmint ~]# ifconfig eth0 netmask 255.255.255.224 8.
Make eth0:0 the default route instead of eth0. The command: netstat -rn will show you what your current default interface is. If it is not eth0:0, delete it with. route delete 0.0.0.0 then add it with something like. route add default eth0:0
Also it is strange, that IP address assigned to eth0:0 in config file is used by eth0. /var/log/messages shows nothing about network configuration errors on either eth0 or eth0:0. system-config-network seem to understand all settings correctly and resaves them ok also. "ifup eth0:0" executes ok, but ifconfig afterwards shows no eth0:0 device ...
eth0 is the first ethernet interface, any additional ethernet interfaces would be named eth1, eth2, etc. Share Improve this answer answered Feb 9 '17 at 12:56 Toby.S 51 1 1 Add a comment Highly active question. Earn 10 reputation (not counting the …
It seems that eth0:0 gets to be the one each time, so by hardcoding GATEWAYDEV="eth0" you make sure that eth0 is always selected as the gateway device. In older versions of RH you could just edit /etc/sysconfig/static-routes and add default via 5.x.y.82 dev eth0 As a last resort /etc/rc.local is always your friend! Share Improve this answer