srch

Owners Manual Pumptec is a microcomputer microcomputer based based pump pump protection device that continuously continuously monitors motor load and power ...

Pumptec pumps are designed and manufactured to withstand rugged use and last for years. Operational conditions or other external factors like clogged nozzles or filters, worn seals, or pinched hoses may diminish performance over time. Use these pump troubleshooting tips to pinpoint and correct potential issues.

Franklin Electric PUMPTEC-PLUS Manual Online: Troubleshooting During Installation. Symptom Unit Appears Dead (No Lights) Flashing Yellow Light Flashing Yellow Light During Calibration Flashing Red and Yellow Lights Flashing Red Light Solid Red Light *Report high or …

Pumptec is a load sensing device that monitors the load on submersible ... B. If the reset time switch is set to manual reset (position 0), Pumptec will not.

12.10.2017 · Full troubleshooting guide can be found in the Franklin Electric AIM Manual: https: ... Full troubleshooting guide can be found in the Franklin Electric AIM Manual: https: ...

QD PUMPTEC The QD Pumptec protects submersible pumping systems and is designed speci˜ cally for use with Franklin Electric’s QD Relay Control Boxes and Franklin 230 V three-wire motors. The QD Pumptec microcontroller continuously monitors line voltage and motor current to protect against over voltage, under voltage and dry well conditions.

Pumptec-Plus measures the actual motor power (Watts), not motor amps or power factor. The motor power draw at the moment of calibration is permanently memorized by Pumptec-Plus. If the motor power draw differs from the memorized calibration power by more than ± 25%, Pumptec-Plus will turn off the pump motor.

Troubleshooting No Lights No power is applied to the Pumptec. Check for voltage at the L1 and L2 connections. If Pumptec is wired downstream of the control switch, the control switch may be open. Solid Load Light Pumptec has detected a dry well or underload condition. A. Make sure the pump and motor are matched correctly.

Troubleshooting No Lights No power is applied to the Pumptec. Check for voltage at the L1 and L2 connections. If Pumptec is wired downstream of the control switch, the control switch may be open. Solid Load Light Pumptec has detected a dry well or underload condition. A. Make sure the pump and motor are matched correctly.

I have outlined some troubleshooting steps below to help investigate problems with your Control Box. Caution! Electricity can be very dangerous, ...

Pumptec-Plus measures the actual motor power (Watts), not motor amps or power factor. The motor power draw at the moment of calibration is permanently memorized by Pumptec-Plus. If the motor power draw differs from the memorized calibration power by more than ± 25%, Pumptec-Plus will turn off the pump motor.

www.franklin-electric.com Installation and Operating Instructions Congratulations on your purchase of a Franklin Electric pump protection system. Pumptec-Plus is the most sophisticated pump protection system on market today. It is designed to work on any 230 VAC single

Overcome Common Pump Problems to Obtain Peak Performance ; Tank is empty · Water valve turned off · Filter clogged · Hoses or tank clogged ; Fill tank. · Turn water ...

Pumptec-Plus Troubleshooting During Installation Pumptec-Plus is a pump/motor protection device designed to work on any 230 V single-phase induction motor (PSC, CSCR, CSIR, and split phase) ranging in size from 1/2 to 5 horsepower.

Pumptec pumps are designed and manufactured to withstand rugged use and last for years. Operational conditions or other external factors like clogged nozzles or filters, worn seals, or pinched hoses may diminish performance over time. Use these pump troubleshooting tips to pinpoint and correct potential issues.

Troubleshooting No Lights No power is applied to the Pumptec. Check for voltage at the L1 and L2 connections. If Pumptec is wired downstream of the control switch, the control switch may be open. Solid Load Light Pumptec has detected a dry well or underload condition. A. Make sure the pump and motor are matched correctly.

Congratulations on your purchase of a Franklin Electric pump protection system. ... If set in the manual position, Pumptec-Plus must be reset manually.

24 rader · The Pumptec is designed for use on Franklin Electric 2- and 3-wire motors (1/3 to 1.5 …

10.04.2018 · Chris shows you how to adjust and calibrate the Franklin Electric QD Pumptec Motor Protection Device.Buy it Here: https://www.rcworst.com/Franklin-Electric-5...

QD Pumptec and the old 2-light version of Pumptec are load sensing devices that monitor the load on submersible pumps/motors.

franklin installation information is available from pump manufacturers and distributors, and directly from franklin electric. call franklin toll free 800-348-2420 for information. warning ... pumptec-plus troubleshooting during installation ...

Troubleshooting After Installation ... *Report high or low line voltage to the power company. ... reactivate the unit. Clean or replace pump intake screen. Remove ...

09.10.2017 · Franklin Electric AIM Manual: https://www.rcworst.com/Shared/content/mfr/franklin_electric/docs/franklinsubmersiblemotorguide2010.pdfIn today's video, we are...