srch

Use the MINI (or MICRO) generic build (broadcom folder) for initial flash from the Linksys firmware.

Newer Linksys firmware overclocks some models of the WRT54GS to 216 MHz, to prevent instability issues inherent in the 2.x versions. The WRT54G(S) v4-v6 and WRT54GL v1.x have a BCM3302 v0.8 processor instead of a BCM3303 v0.7 with previous models.

Newer Linksys firmware overclocks some models of the WRT54GS to 216 MHz, to prevent instability issues inherent in the 2.x versions. The WRT54G(S) v4-v6 and WRT54GL v1.x have a BCM3302 v0.8 processor instead of a BCM3303 v0.7 with previous models.

Check the firmware version in the top right corner to be 4.71.4, otherwise flash: ... Go to Administration -> Firmware Upgrade, select dd-wrt.

Firmware. Ver.4.21.5. Latest Date: 02/24/2012. Download 3.20 MB. Release Notes. NOTE: After downloading the firmware, you need to load the file to your router to improve its functionality. For instructions on how to update the firmware of your Linksys router using the classic web-based setup page, click here.

This tutorial will walk you every step of the way through flashing your Linksys WRT54G (version 8) router to use the DD-WRT firmware.

[edit] Initial Flash · Power cycle the router, then after boot go to 192.168. · Enter "root" as the username and "admin" as the password · Go to ...

11.09.2008 · This tutorial will walk you every step of the way through flashing your Linksys WRT54G (version 8) router to use the DD-WRT firmware. According to Wikipedia, the Linksys WRT54G v8.0 is “currently one of the most commonly available (routers) at US retail establishments, such as Best Buy and Target”. Due to hardware limitations, the 8.x … How to …

6. Access the DD-WRT GUI at 192.168.1.1 De-brick. With the first .bin file I installed from the Linksys GUI Admin options, upload went about half way then tried to reboot, and bricked my WRT54GSv7. With this procedure (external link), using this command from the .bin file location worked, but had to hit enter TWICE to execute the command to ...

Details are here. Initial flash: download mini_generic.bin. Perform a Hard_reset_or_30/30/30 reset; Upload dd-wrt through the firmware update ...

PROBLEM AND WORKAROUND TO AN INACCESSIBLE LINKSYS WRT54G V6.0 ROUTER--- may be good for V5 as well. problem: power led blinking rapidly, ... No problems at all during install following steps above. WRT54G v6 running Firmware: DD-WRT v24-sp2 (10/10/09) micro directly, did _not_ use 12548 Newd_Micro.bin > upgrade, ...

7) Once in the dd-wrt webgui go to Administration > Factory Defaults and select to restore factory defaults. 8) This will hard reset your router, which will take about 2-3 minutes to complete. 9) After it is finished you can then re-access the dd-wrt webgui at 192.168.1.1, it will again want you to set a user/pass, go ahead and do so, then ...

Download and unzip OEM firmware [1] · As above, reset then go to the DD-WRT GUI, enter a username/password · Go to Administration->Firmware ...

NOTE: Replacing the factory firmware is different for every router. In this example we will replace the firmware on a Linksys WRT54GL .If you have a different router, find your solution here to replace the factory default firmware with DD-WRT.

The WRT54GL router must already have dd-wrt installed before you begin this process. 1 -First start by backing up your current CFE.BIN file and keep it in a safe place 2- Enable ssh services in the dd-wrt configuration at 192.168.1.1.

NOTE: Replacing the factory firmware is different for every router. In this example we will replace the firmware on a Linksys WRT54GL .If you have a different router, find your solution here to replace the factory default firmware with DD-WRT.

The standard clock speed of a WRT54G(S) v2-v6 is 200 MHz. DD-WRT allows overclocking the device to up to 300 MHz for v2-v3 and up to 250mhz for ...

[edit] Initial Flash · Restore factory defaults in the Linksys firmware. · Go to the tab Administration > Firmware Upgrade and select the ...

3. again go to the firmware upgrade page and browse to the VxWorksKiller-Gv72-v3.bin file, and click on the upgrade page. Wait for 60 seconds for it to reboot on its own, if it does not then powercycle the router manually. 4. Tftp the DD-WRT firmware to the router dd-wrt.v24_micro_generic.bin, after sucessful tftp, wait 3 min for the router to ...

The Linksys WRT54G is a very old router that can still be very useful with 3rd part Firmware from DD-WRT. The WRT54G was once a very ...

The WRT54GL router must already have dd-wrt installed before you begin this process. 1 -First start by backing up your current CFE.BIN file and keep it in a safe place 2- Enable ssh services in the dd-wrt configuration at 192.168.1.1.