srch

08.02.2021 · Hello everybody, I just setup a new computer in order to do a fresh installation of Manjaro… The processor is an AMD TR 1950X and the motherboard is an ASRock X399 Taichi. This motherboard allows to setup RAID array. I successfully managed to setup the array (I had 3 SSD of 500Gb) and it appear in the bios as a 1.5Tb RAID0. However, once I’m on the live …

In Manjaro, e2fsprogs is already installed Btrfs. A modern Copy on Write filesystem for Linux aimed at implementing advanced features while also focusing on fault tolerance, repair and easy administration. Btrfs not only is a filesystem, but also is partly a volume manager, software-raid, backup-tool, and it is flash-friendly.

04.02.2019 · Arch Linux is a general-purpose Linux distribution for x86-64 computers and is very popular among the intermediate and advanced Linux users. It is free and open-source software. In this blog, we will check out how to install Arch Linux by setting software RAID 1. Install Arch Linux

This is the recommended mdadm partition type for RAID arrays on Arch Linux. 0xFD for RAID autodetect arrays ( Linux ...

15.09.2017 · Raid can be done with manjaro-architect by manually creating it, mounting it under /mnt and setting appropriate hooks to mkinitcpio.conf. But yes, unfortunately there is no automation of any kind for RAID yet. Btrfs raid is pretty easy to do and can also be added after the fact, but we are probably talking about mdadm here, right?

I mean a completely new hardware (no existing software RAID exists), so installer should create RAID first and then install everything on it ...

RAID 6 Requires 4 or more physical drives, and provides the benefits of RAID 5 but with security against two drive failures. RAID 6 also uses striping, like RAID 5, but stores two distinct parity blocks distributed across each member disk.In the event of a failed disk, these parity blocks are used to reconstruct the data on a replacement disk.

I can't find Software RAID on the Wiki or in this forum, and not much on Manjaro Architect Installer ether. I'm switching from openSUSE* and ...

Is it possible to install manjaro on a NVME drive configured with Intel RST? Would mdadm be able to help and how would that work?

Manjaro provides an easy-to-use tool that will do all work for you. More information about this in our wiki. Search and install software. • Search for “octopi” or “pamac” in your application menu and open it. • Browse through the list or search using the search bar. • …

Please, how to install Manjaro via the standard installer or the Architect on /dev/md/XXX mdadm built SW RAID device?

Use set the drivers and independent drives in the BIOS and set them up using mdadm, the linux software RAID. Edit: I noticed you want a RAID0 ...

Hello everybody, I just setup a new computer in order to do a fresh installation of Manjaro… The processor is an AMD TR 1950X and the ...

Hi, I want to setup two computers with raid installations(RAID 0 and RAID 1) using ... partition software RAID can be mounted and installed into using m-a.

Install Arch Linux with Fake RAID. From ArchWiki. The purpose of this guide is to enable use of a RAID set created by the on-board BIOS RAID controller and thereby allow dual-booting of Linux and Windows from partitions inside the RAID set using GRUB. When using so-called "fake RAID" or "host RAID", the disc sets are reached from /dev/mapper ...

Hey there, I have two 500 gb ssd drives, and I want them to be set up in a RAID 0 array using software RAID. I'll be reinstalling Manjaro ...

19.05.2019 · Notes from the video are available in the link below.https://github.com/andrew-klassen/manjaro_architect_uefi_raid

Notes from the video are available in the link below.https://github.com/andrew-klassen/manjaro_architect_uefi_raid.

Installation guides for every release of Manjaro have been provided below for both beginners and experienced users. These guides may also be used to install Manjaro as a main operating system, or within a virtual machine environment using Oracle's Virtualbox. Rebooting your computer (or starting your virtual machine) after connecting your ...

21.05.2021 · Removing software using Pamac is as easy as installing it. All you have to do just click on the “remove” button on the right side of the screen. Once you selected all the packages you want to remove, click on “apply” button. Method 2: Install and Remove Software in Manjaro Linux with Octopi.