srch

In Backup Exec (tm) for Windows Servers and Backup Exec for NetWare Servers, the Network Data Management Protocol (NDMP) is used by Backup ...

When a media server makes a connection with a remote system, the initial connection will be initiated on NDMP port 10000. The Remote Agent will be listening for ...

22 rader · 17.11.2017 · Backup Exec ports. You may have special port requirements for Backup …

08.09.2011 · I enabled NDMP on the filer the other day to allow me to monitor snapmirror relationships with the Disaster Recovery module in DFM. Since doing that, Backup Exec cannot connect to the CIFS shares to perform backups. Browsing CIFS shares is fine, only the backup jobs fail. If I disable NDMP on the filer, the backups work again.

Ports opened on the Backup Exec Server and systems using the Remote Agent for Windows Systems ... and changing the NDMP port to an alternate port number.

With the introduction of Remote Agent for Linux & UNIX Servers (RALUS) , Backup Exec now uses well known NDMP port 10000 for UNIX\Linux ...

05.12.2017 · Note: For Backup Exec 11 and higher, if Remote Agent publishing is enabled, it is only necessary to make the above change on the specific server(s) where port 10000 is in use. On the server(s) where this change is necessary, ensure that the new NDMP port is allowed both inbound and outbound access through the firewall on the remote system.

In Backup Exec for Windows Servers, Network Data Management Protocol (NDMP) is used by Backup Exec to communicate with the remote servers.

Mar 29, 2018 · 1. When using the Enterprise Vault agent for Backup Exec and server aliases are being used, the Backup Exec server NDMP port must match the NDMP port setting on any server that has an alias. This is because a server typically advertises its NDMP port to the Backup Exec server but in the case of an alias, the alias name is not advertised. 2.

Best practices for Backup Exec NDMP Option · Match the port number that Backup Exec uses to the port number that the device's NDMP service uses ...

15.08.2005 · NDMP TCP/IP port 10000. 08-16-2005 10:13 AM. Over the last two weeks the Backup Exec Remote Agent service stops in the mail server. I found the following message in the Event Viewer: "The Backup Exec Remote Agent for Windows Servers Service did not start. The NDMP TCP/IP port 10000 is already in use. Please make sure that no other TCP/IP ...

Apr 30, 2013 · NDMP to Backup Exec 2012 Hi All, we are looking to backup CIFs servers on our VNX5500 to tape (tape library is connected to the Backup Exec server, not the VNX) via NDMP and Backup Exec 2012. I have read and followed the EMC configuring NDMP Backups on VNX guide whith the only change on the VNX being to add a user and password:

Sep 10, 2013 · To install the NDMP Option on the local Backup Exec server: Click on Backup Exec icon towards top left corner of Backup Exec Admin Console -> Installation and Licensing -> Install Options and Licenses on this Backup Exec Server. On the Add Licenses screen, make sure of NDMP option is installed.

30.04.2013 · NDMP to Backup Exec 2012 Hi All, we are looking to backup CIFs servers on our VNX5500 to tape (tape library is connected to the Backup Exec server, not the VNX) via NDMP and Backup Exec 2012. I have read and followed the EMC configuring NDMP Backups on VNX guide whith the only change on the VNX being to add a user and password:

29.03.2018 · In some situations if a conflict arises with the default NDMP port 10000 i.e. if port 10000 is used by another application or service and the Backup Exec Job Engine service is unable to establish a connection, the default port can be changed to another port number by modifying the services file located under <systemroot>\System32\Drivers\etc.

Dec 05, 2017 · In Backup Exec for Windows Servers, Network Data Management Protocol (NDMP) is used by Backup Exec to communicate with the remote servers. The Backup Exec Job Engine first communicates with the Remote Agent for Windows Servers through a control session using port 10000.

10.06.2008 · I have Backup Exec 11d with the NDMP option server on the same network LAN as the EMC. On the EMC side, I think I created everything correctly, since the tape device shows up. The NDMP service is running on port 10000. When I try to add a NDMP server on Backup Exec, i get the following eror message: "Unable to validate the NDMP server at this time.

14.07.2020 · Click Yes to restart Backup Exec services. After services restart you will see the Netapp is added. Now you will also see that Netapp is automatically added and listed under servers in Backup and Restore option as well. Now Netapp storage is ready to be backed up. Related Post : How to backup NDMP Filer (NetApp Storage) in Backup Exec 20

10.09.2013 · NDMP is an Internet-Draft standard that uses port 10000 by default. The Veritas Backup Exec NDMP Option lets Backup Exec use the Network Data Management Protocol (NDMP) to initialize and control backups and restores of Network Attached Storage (NAS) devices such as NetApp filers as explained below.

The Agent for Windows (AWS) or Backup Exec Remote Agent for Windows Servers (RAWS) service by default uses port 10000. This is the industry ...

Backup Exec uses Network Data Management Protocol (NDMP) to communicate with remote servers that are running the Backup Exec Remote Agent for ...

Aug 16, 2005 · NDMP TCP/IP port 10000. 08-16-2005 10:13 AM. Over the last two weeks the Backup Exec Remote Agent service stops in the mail server. I found the following message in the Event Viewer: "The Backup Exec Remote Agent for Windows Servers Service did not start. The NDMP TCP/IP port 10000 is already in use. Please make sure that no other TCP/IP ...

Click the Backup Exec Button · Click Configuration and Settings | Backup Exec Settings · Click Network and Security · Select the Enable remote ...

14.01.2021 · For Backup Exec for Windows Servers version 11 and later the NDMP ports for Media Server and Remote Agent can be different if publishing is enabled for the Backup Exec Remote Agent. After changing the NDMP port on a remote server, ensure that the firewall on the remote server allows both inbound and outbound access for the new port.

Default port: 10000. 1. PORT STATE SERVICE REASON VERSION. 2. 10000/tcp open ndmp syn-ack Symantec/Veritas Backup Exec ndmp. Copied!

Click Data Protection > NDMP > NDMP Settings. In the Service area, click Enable NDMP Service. In the Port number field, specify a port number through which a data management application (DMA) can connect to the Isilon cluster. The default port number is 10000. Optional: From the DMA vendor list, select the name of the DMA vendor to manage ...