srch

Since name server is status down because of ICMP block , it wont try to resolve any hostname although again required DNS resolution port is ...

Good morning, I've setup a new test VPN gateway on my NS 11.1 pair and my test clients can connect however they can't reach anything unless they use the ...

DNS Servers and Suffix – enable DNS resolution across the VPN tunnel ... Policies apply to all NetScaler Gateway connections, not just VPN.

Solution 1: Add an SNIP in the NSIP subnet if you see below counters increasing indicating that ADC is not able to open a connection to the server due to port allocation errors: 3295 0 58 4 0 dns_tot_ServerQueries Wed Jul 20 08:04:55 2016. 3296 0 4 2 0 dns_err_NoDomains Wed Jul 20 08:04:55 2016. 3297 0 5704 2 0 dns_tot_Queries Wed Jul 20 08:04 ...

05.05.2021 · DNS usually needs to function across the VPN tunnel. Go to Traffic Management > DNS > Name Servers to add DNS servers. In ADC 13.0 build 71.44 and newer, VPN plug-in for Windows supports Secure DNS update. This feature is disabled by default. To enable it, create the following on the client device: (source = 13.0-71.44 release notes) 💡

This article describes how to enable Citrix ADC appliance to use DNS for resolving the hostnames to its respective IP addresses.

16.02.2018 · KB ID 0001402 Problem I’ve been setting up a VPN solution on the test bench as I’m looking at Always On VPN. When I noticed that I had a problem with my remote VPN connections on Windows 10. They would connect fine but I could not resolve any FQDNs for my domain? Solution By default, […]

Note: These IP address do not belong to the NetScaler. The IP addresses + DNS port combo cannot be defined on the NetScaler in the Load ...

Solution 1: Add an SNIP in the NSIP subnet if you see below counters increasing indicating that ADC is not able to open a connection to the server due to port allocation errors: 3295 0 58 4 0 dns_tot_ServerQueries Wed Jul 20 08:04:55 2016. 3296 0 4 2 0 dns_err_NoDomains Wed Jul 20 08:04:55 2016. 3297 0 5704 2 0 dns_tot_Queries Wed Jul 20 08:04 ...

01.11.2019 · I just tried turning off IPv6 with no change, VPN users still try to access the WAN when a host name is contacted vs accessing the VPN corporate network. There is no DNS vServer listed in the pull down, I'm not 100% certain how to set up one. Prior to the 11.1 upgrade (when we had 10.5) this worked on the VPN just fine so I didn't need a DNS ...

Jul 13, 2016 · I just tried turning off IPv6 with no change, VPN users still try to access the WAN when a host name is contacted vs accessing the VPN corporate network. There is no DNS vServer listed in the pull down, I'm not 100% certain how to set up one. Prior to the 11.1 upgrade (when we had 10.5) this worked on the VPN just fine so I didn't need a DNS ...

Prior to this week, 100% of our connections to the resources in that data center have been remote (citrix) desktop sessions, across the internet ...

So this is something I've struggeled a bit with in the past, also see it on a couple of forums post on Citrix, and there are as always not ...

22.05.2017 · Citrix netscaler not resolving external dns request. We are in the implementation phase of the netscaler vpn solution and we have found the session establishes successfully. During the session internal DNS is able to resolve to the internal DNS server however not within the defined scope is unable to resolve.

22.01.2020 · The DNS servers and suffixes configured for VPN connections are used in Windows 10 to resolve names using DNS in the Force Tunneling mode (“Use default gateway on remote network” option enabled) if your VPN connection is active.In this case, you cannot resolve DNS names in your local network or have Internet access using your internal LAN.

When I try to ping or dig the hostname/cname "hostname", the Netscaler cannot resolve this hostname, nor it appends my configured DNS suffix. When I enter the FQDN "hostname.domain.com" the netscaler resolves it to an IP address. Any ideas? The device is an MPX 5550 NS 11.1 48.10nc (HA setup) this article does NOT help since I already mentioned ...

This article describes how to configure sample Domain Name Service (DNS) Lookup on NetScaler by using recursive queries. Recursion refers to the process of having the DNS server itself making queries to other DNS servers on behalf of the client who made the original request.

Dec 15, 2015 · “DNS-TCP” is not supported in a DNS Forward Proxy Deployment and any DNS Queries triggered through the VPN Module. The UDP to TCP switching happens only for the Queries generated by NetScaler mainly for resolving Domain Based Services(KDC resolution is one such example).Basically it not because the request is forwarded, it is because once the DNS API return truncated flag the cvpn module ...

Jan 22, 2020 · It is not secure since the external DNS servers (specified for your VPN connection) can potentially see your DNS traffic (the leak of your DNS requests). You can disable the SMHNR in Windows 10 via the GPO: Computer Configuration -> Administrative Templates -> Network -> DNS Client-> Turn off smart multi-homed name resolution = Enabled.

I have fixed this problem permanently by manually setting the metric of my LAN connection to a higher value than the metric of the VPN connection.

Feb 18, 2015 · So therefore I decided to write this post, since both DNS and LDAP are crucial in adding to the Netscaler. So lets start with DNS. There are a couple of ways to add DNS on the Netscaler. Either its UDP, TCP or TCP & UDP. Now UDP is the one that is typical used since a default DNS uses UDP, TCP is more for Zone transfers and so on.

Repeat steps 5 and 6 to add a recursive DNS server that will resolve requests if NetScaler cannot reach ETP. Command line interface. How to. Establish an SSH ...

Some (but not all) of our Windows 10 users are having a DNS problem when ... common for windows 10 users when it comes to SSL VPN, I have managed to resolve ...

18.02.2015 · So therefore I decided to write this post, since both DNS and LDAP are crucial in adding to the Netscaler. So lets start with DNS. There are a couple of ways to add DNS on the Netscaler. Either its UDP, TCP or TCP & UDP. Now UDP is the one that is typical used since a default DNS uses UDP, TCP is more for Zone transfers and so on.