srch

27.06.2016 · You can take a look on the calibration data in the "art" partition.If your MAC address is stored in it then you can change it. root@OpenWrt:/# cat /proc/mtd dev: size erasesize name mtd0: 00030000 00010000 "u-boot" mtd1: 00fc0000 00010000 "firmware" mtd2: 00120000 00010000 "kernel" mtd3: 00ea0000 00010000 "rootfs" mtd4: 00c60000 00010000 "rootfs_data" …

As you can tell, the MAC addresses are separated by spaces. Now write the changes to the system configuration: uci commit. Finally, restart the ...

This page showcases some basic batman-adv configurations on OpenWrt including wireless ... 15 # change throughput_override to 0 to use automatic detection; ...

I'm trying to set up a WiFi network with a custom BSSID. While minor MAC/BSSID address change works fine, significant one cause an error.

I'm playing around with networking and I want to spoof a MAC of another device. But even when I change the MAC I still see the MAC in the dropdown list of wifi networks under "BSSID". I added "option bssid 'oldmac'" to the -iface and -device sections of /etc/config/wireless but I still see the hardware MAC. TY

03.11.2021 · Set your PC's ethernet or Wi-Fi settings at static IP 192.168.2.10 and default gateway 192.168.2.1, then connect again to the wifi repeater (through ethernet or wifi). When you finish all of the following steps, remember to reset your PC's IP address back to the original address (or DHCP), otherwise you won't have Internet access.The repeater won't route traffic …

By the network for the secondary router (the one with Mode: Master) click Edit; Under Interface Configuration set ESSID to the same SSID as the primary router ...

hi i have tplink td-w8970 with Openwrt 40335. my problem is: the bssid change at every reboot of Router. i change config in etc/config/wireless/ config wifi-iface

Note: for some devices BSSID of disabled networks may still behave the old way and display data from another active network on the same radio, instead of "00:00:00:00:00:00". This may require more research as self.iwdata.bssid always returns "00:00:00:00:00:00" even for active networks, so self.iwinfo.bssid must be used as a backup option to ...

I'm playing around with networking and I want to spoof a MAC of another device. But even when I change the MAC I still see the MAC in the dropdown list of wifi networks under "BSSID". I added "option bssid 'oldmac'" to the -iface and -device sections of /etc/config/wireless but I still see the hardware MAC. TY

When you physically move your laptop from one room to another, the BSS you use can change because you moved from the area covered by one access point to the ...

Usually for OpenWRT (including 19.07) it changes the MAC/BSSID in wifi signal to add 'option bssid 00:00:00:00:00:00' But now 3.203 does not ...

01.11.2021 · Wi-Fi automatic channel selection with iwchan This article relies on the following: * Accessing OpenWrt CLI * Managing configurations * Managing packages * Managing services Introduction * This instruction provides a method to automatically select a wireless channel. * It calculates the load to frequency distribution and selects the channel with the least load.

Firmware 1.9.5.0 from Asus implements the multiple BSSID feature : several AP with different SSID and different security settings ... It would be nice to get the same feature into OpenWRT. ... (and maybe changing a few small things in wlcompat).

Mar 08, 2020 · According to another dev I asked, it is a hardware limitation. The hardware uses a bit field internally to track the used BSSIDs. Due to that, it is only possible to set BSSIDs in the range phy base address .. phy base address + 16.

comment:1 Changed 4 years ago by nbd. Resolution set to not_a_bug. Status changed from new to closed. the 'bssid' option is used to select the remote bssid to connect to. if you want to change the local address (= bssid in AP mode), use the 'macaddr' option in the same section.

Nov 21, 2021 · OpenWrt : The broadcasted SSID of the wireless network and for for managed mode the SSID of the network you’re connecting to : bssid: BSSID address : no (driver default) Override the BSSID of the network, only applicable in adhoc or sta mode. In wds mode specifies the BSSID of another AP to create WDS with. mesh_id: Mesh ID : no : none

But even when I change the MAC I still see the MAC in the dropdown list of wifi networks under "BSSID". I added "option bssid 'oldmac'" to ...

Jan 28, 2010 · 29 Jan 2010, 00:53. The fact is that I can add "bssid" in "wifi-device" config in "wireless" file, and I can also change the Mac address for the interface in Luci. But none of this takes any effect. Although the interface status shows a change of mac address when I change it in Luci. The signal I pick up with network stumbler still shows the ...

01.04.2015 · 一群计算机设定相同的BSS名称，即可自成一个group，而此BSS名称，即所谓BSSID。. 通常，手机WLAN中，bssid其实就是无线路由的MAC地址. ESSID 也可认为是SSID, WIFI 网络名. SSID. SSID是Service Set Identifier的缩写，意思是：服务集标识。. SSID技术可以将一个 无线局域网 分为 ...

28.01.2010 · 28 Jan 2010, 23:55. If it is Ad-hoc mode, I think you can. But I cannot find options for changing BSSID in AP mode either. Post #3. andrew574. 29 Jan 2010, 00:53. The fact is that I can add "bssid" in "wifi-device" config in "wireless" file, and I can also change the Mac address for the interface in Luci. But none of this takes any effect.

12.03.2020 · Set the first byte to x2, x6, xA, or xE (in other words, bit 1 is set). That flags it as a locally administered MAC. MACs without that bit set should comply with the OUI system to ensure they are globally unique. The manufactuer sets these.

21.11.2021 · bssid: BSSID address : no (driver default) Override the BSSID of the network, only applicable in adhoc or sta mode. In wds mode specifies the BSSID of another AP to create WDS with. mesh_id: Mesh ID : no : none : The Mesh ID as defined in IEEE 802.11s. If set, the wireless interface will join this mesh network when brought up.