Du lette etter:

openwrt fstab not working

Swap file not mounting on boot - Installing and Using OpenWrt
https://forum.openwrt.org › swap-f...
I'm not sure that's the problem because when I try swapoff and on with the -a attribute (I believe that re-reads the /etc/fstab config) it ...
[OpenWrt Wiki] Extroot configuration
https://openwrt.org/docs/guide-user/additional-software/extroot_configuration
28.11.2021 · Extroot configuration This article relies on the following: * Accessing OpenWrt CLI * Managing configurations * Managing packages * Managing services Introduction This guide describes how to configure OpenWrt to use a storage device (USB or SATA or SD card or whatever) to expand your root filesystem, to install freely all the packages you need.
Reload fstab configurations - Installing and Using OpenWrt
https://forum.openwrt.org › reload...
Is there any difference between this: block umount && block mount; (taken from here) And this: /etc/init.d/fstab boot (taken from here) And ...
[OpenWrt Wiki] Fstab Configuration
openwrt.org › docs › guide-user
Aug 10, 2021 · The fstab UCI subsystem is where all the options for all devices and file systems to be mounted are defined, the actual file is located at /etc/config/fstab. By default this subsystem and its configuration file do not exist, as for the average OpenWrt usecase (network devices) it's not needed.
Fstab not mounting - Installing and Using OpenWrt
https://forum.openwrt.org › fstab-n...
I've set up fstab to automatically mount my usb drive but it doesn't ... installed all the kernel modules necessary but it's not working.
[solved] Mounting NTFS device problem - OpenWrt Forum
https://forum.openwrt.org › solved...
... Linux Kernel : 4.4.92 Problem:NTFS device cannot be mounted by 'block mount' command when option 'big_writes' was added to fstab.
[OpenWrt Wiki] Mounting Block Devices
https://openwrt.org › block_mount
block-mount contains the code that does the actual mounting, and the mounting via /etc/init.d/fstab (i.e. on boot rather than when device is ...
Boot errors on fstab - For Developers - OpenWrt Forum
https://forum.openwrt.org › boot-e...
... kmodloader: loading kernel modules from //etc/modules-boot.d/* ... [ 7.192393] block: unable to load configuration (fstab: Entry not ...
Extrooting not working - Installing and Using OpenWrt
https://forum.openwrt.org › extroo...
I am trying to get extroot to work on OpenWRT 19.07.7 (x86_64 on PCEngines APU2). ... for some reason fstab entry is not found:
Topic: Cannot configure FSTAB to automount USB drive
https://forum.archive.openwrt.org › ...
For the sake of troubleshooting I have installed a fresh copy of OPENWRT (openwrt-brcm-2.4-squashfs) on my ASUS WL500GPv2.
Fstab not mounting - Installing and Using OpenWrt ...
https://forum.openwrt.org/t/fstab-not-mounting/2820
27.04.2020 · I'm having the same problem on a wrt3200acm of not automounting after a reboot. I've fresh upgraded to OpenWrt 19.07.1, formatted my USB HDD for ext4 and set my delay to 30. Reboot and the LEDs don't light up recognizing the USB drive until I unplug and replug in the drive. I not trying to hijack anyone's post, if I need to make a new post, I will.
[OpenWrt Wiki] System configuration not handled by UCI
openwrt.org › docs › guide-user
Apr 10, 2019 · A symlink to /tmp/fstab which is being created and configured by UCI in /etc/config/fstab. This is an ASCII file which defines the groups to which users belong to. Executed by init every boot. Routing tables configuration. See: iproute2. In OpenWrt the Kernel is executed by the bootloader with the option init=/etc/preinit (instead of the usual ...
[resolved]USB storage failures - forum.openwrt.org
https://forum.openwrt.org/t/resolved-usb-storage-failures/116691
1 dag siden · MarkP2015 January 8, 2022, 7:56pm #7. /mnt/sdb1 is a 4 gig flash drive for extended storage. root@OpenWrt:/# mount -a mount: mounting UUID=e8577c39-a69c-4a4e-8717-26de715249ec on /mnt/sda1 failed: No such file or directory. is a 500gig external drive holding multimedia (for samba, eventually, after this mess I've made is fixed.)
Fstab entry for cifs - Installing and Using OpenWrt
https://forum.openwrt.org › fstab-e...
Can anyone give me an fstab entry for using cifs? I can mount from the command line ... This will definitely not work in /etc/config/fstab!
Fstab not mounting - Installing and Using OpenWrt - OpenWrt Forum
forum.openwrt.org › t › fstab-not-mounting
Apr 03, 2017 · I'm having the same problem on a wrt3200acm of not automounting after a reboot. I've fresh upgraded to OpenWrt 19.07.1, formatted my USB HDD for ext4 and set my delay to 30. Reboot and the LEDs don't light up recognizing the USB drive until I unplug and replug in the drive. I not trying to hijack anyone's post, if I need to make a new post, I will.
[OpenWrt Wiki] Mounting Block Devices
openwrt.org › docs › techref
May 21, 2020 · The mounting of block devices is handled by the block-mount source package, which contains the block-mount and block-hotplug packages.block-mount contains the code that does the actual mounting, and the mounting via /etc/init.d/fstab (i.e. on boot rather than when device is hotplugged), and block-hotplug takes care of mounting devices when the device is recognized by the system (.e.g. when ...
[OpenWrt Wiki] Extroot configuration
openwrt.org › docs › guide-user
Nov 28, 2021 · In the first case OpenWrt will not want to read the configuration of /etc/config/fstab ; in the latter case you can work around it by mounting the external/additional disk directly to /. Instructions 1.
OpenWrt Forum Archive
https://forum.archive.openwrt.org/viewtopic.php?id=32812
27.01.2018 · This is a read-only archive of the old OpenWrt forum. The current OpenWrt forum resides at https: ... Topic: Fstab not mounting cifs at boot or through CLI. The content of this topic has been archived on 23 Apr 2018. There are no obvious gaps in this topic, but there ... I already follow this step but still not work ...
[OpenWrt Wiki] Fstab Configuration
https://openwrt.org/docs/guide-user/storage/fstab
10.08.2021 · Fstab Configuration The Fstab, or file systems table, is a central configuration that defines how file systems (usually on block devices) should be mounted if requested (such as on booting the device or connecting it physically). This way, you don’t have to manually mount your devices when you want to access them. The mounting configuration can consist of static file …
[OpenWrt Wiki] Fstab Configuration
https://openwrt.org › docs › storage
The mounting configuration can consist of static file systems but ... as for the average OpenWrt usecase (network devices) it's not needed.