srch

internet connectionipv6openwrtrouter ... I see the gateway as probably local-only address, is that the problem due to which I cannot browse IPv6-only sites?

27.11.2021 · IPv6 configuration See also: Routing example: IPv6, IPv4/IPv6 transitioning The default firmware provides full IPv6 support with a DHCPv6 client (odhcp6c), an RA & DHCPv6 Server (odhcpd) and a IPv6 firewall (ip6tables). Also, the default installation of the web interface includes the package luci-proto-ipv6

I try to put IPv6 assignment length to 64 and IPv6 assignment hint to 1 on lan interface, and now my OpenWRT router has the same address ...

13.03.2021 · What if you want to manage an IPv4-only device from your IPv6-only network? Using a small OpenWrt router, it is possible to create a small dual-stack island network. OpenWrt 19.07.x supports jool a really useful v4<–>v6 translation tool.

Documentation · User guide · Network · IPv6 · How to use OpenWrt behind a Freebox Crystal with IPv6 bridge · How to use OpenWrt behind a ...

My Lan do have an public IPv6 address, but I hope it doesn't have it. As for WAN, it only has an IPv6-PD. It should have an IPv6 address as well. I always have both IPv6 address and PD in the past, but it only has PD this time.

I use the following settings, but still get ipv6 address on lan interface: uci set 'network.lan.ipv6=off' uci set 'dhcp.lan.dhcpv6=disabled' ...

27.11.2021 · How to use OpenWrt behind a Freebox with IPv6 delegation. IPv6 configuration. IPv6 extras. IPv6 multicast. IPv6 on L2TP softwire. IPv6 with Hurricane Electric. IPv6 with Hurricane Electric using LuCI. NAT6 and IPv6 masquerading. WIDE-DHCPv6 client configuration.

In a nutshell: Stateful DHCPv6 auto-configuration of IPv6 is the equivalent of DHCP in IPv4. A DHCPv6 service provides the IPv6 address to the client device ...

27.11.2021 · This guide relies on OpenWrt default settings and assumes you already have a working IPv6connection on your OpenWrt router. Instructions 1. Preparation Install the necessary packages. # Install packagesopkg update opkg installkmod-ipt-nat6 2. Network and DHCPv6 Enable IPv6 by defaultand announce the default IPv6 routeif necessary. 3. Firewall

My server is running on a shelf at home, behind an OpenWRT router. I get my IPv4 address at the WAN interface with DHCP.

I found an issue with the IPv6 interface configuration when applying an assignment of a PD subprefix and a static IPv6 address in OpenWrt ...

This example is for IPv6 tunnels only, and does not apply to native dual-stack interfaces.. The example below assumes your tunnel interface is configured on it's own zone. An alternative setup that may also be used is having your IPv6 tunnel on an interface like henet and attached to the wan zone. This is also correct, but if you plan on passing a prefix down to your LAN and want to …

25.11.2018 · To test the setup you’ll need either a VPS with IPV6 enabled or use online tools like this one. Once done with the firewall, IPv6 address of the router will be directly accessible from outside, but none of the computers on our internal network. On the other hand, all computers inside our network will be able to use IPv6 sites with no problems.

This is causing IPv6 queries to not be filtered, and my devices to only partially display within the PiHole interface. I cannot figure out how to stop OpenWrt from providing itself as a DNS. Screenshots and info: OpenWrt 18.06 PiHole 4.3.1 TpLink Archer C7 OpenWrt IPs: ...

The domain downloads.openwrt.org has an IPv4 address but no IPv6 address. So you cannot reach it over IPv6 unless you use a translation mechanism. You could use NAT64 to be able to create a TCP connection to that IPv4-only server from an IPv6-only client. But why would you be using an IPv6-only client?

27.11.2021 · IPv4 configuration Due to obvious reasons, IPv4 is fully supported in default firmware. Upstream configuration for WAN-Interfaces The following sections describe the configuration of IPv4 connections to your ISP or an upstream router. For an uplink with native