srch

26.12.2021 · package: luci-app-ddns. This website uses cookies. By using the website, you agree with storing cookies on your computer.

to disable NAT on the OpenWrt router, but keep its routing (and firewall) on routing on the ISP router is also enabled you have to define non-overlapping IP ranges and static IP addresses for the two routers as OpenWrt's NAT is disabled, you need to manually set static routes, such that clients on both routers can send traffic to the other router

When I click to add it do: firewall.cfg353837=redirect firewall.cfg353837.enabled=1 But it does not show in snat section of luci...

Hi, I'm struggling whole day to set up correct rules for Nat and firewall. Earlier I had no problem to set everything on OPNsense, ...

fullcone nat加速. 从此忘记你只能一对一的 dmz 吧！fullcone nat 采用 stun 模式，使你的 udp nat报文应用 始终具有 nat1 的 high id ，对 游戏联机，p2p 下载，各种挂机宝极大增强的互联几率，获得更小的延迟，更大的udp互联速率！ 同时兼容 upnpd, 请同时开启获得更好的效果。

16.12.2021 · OpenWrt's firewall management application fw3has three provisioning mechanisms Configuration files: /etc/firewall.user /etc/config/firewall Most of the information in this wiki will focus on the configuration files and content. The LuCI and UCI interfaces are user abstractions, ultimately modifying the configuration files. Management

1 Log into your router using your username and password (Default IP: 192.168.1.1, Username: root, default password: none) · 2 Click on "Network" then "Firewall" ...

d/firewall/10-nat-reflection only starting from 10.03.1-rc4 (which I am running), but LuCI 0.9 is only able to assign redirects into "lan" zone.

Finally i just fixed the issue by following these instructions https://wiki.openwrt.org/doc/howto/clientmode#routed. Basically it sums up to define a static ...

I decided to try using ip an iptables rather than UCI. I'm going to try pasting the following in /etc/firewall.user tomorrow morning (PST). How does it look?

27.09.2021 · LuCI essentials This article relies on the following: * Accessing OpenWrt CLI * Managing configurations * Managing packages * Managing services Introduction While OpenWrt can be managed completely using SSH and the terminal, the LuCI WebUI makes many administration tasks easier. The OpenWrt full releases, such as the current 18.06.x series, ship …

30 rader · What is LuCI LuCI was founded in March 2008 as “FFLuCI” as part of the efforts to …

27.11.2021 · NAT6 and IPv6 masquerading This article relies on the following: * Accessing OpenWrt CLI * Managing configurations * Managing packages * Managing services Introduction This page describes how to set up NAT6 aka NAT66 with IPv6 masquerading on your OpenWrt router. Most users will not need or want to do this in IPv6, but there are some more specific …

02.08.2020 · Hi, I'm struggling whole day to set up correct rules for Nat and firewall. Earlier I had no problem to set everything on OPNsense, but I moved to OpenWRT because of better drivers and more open architecture. In OPNsense I was able to set rules like: Any traffic from LAN that destination IP is in TUN1 to be redirected to TUN1 Any traffic from LAN that destination IP is in …

How to do that? In OpenWRT I see that there is an IP address shown: Protocol: PPPoE Address: 100.65.xx.xxx/32 Also, when you installed luci-app-upnp, did you make sure to start the service in System->Startup? By default, the service is enabled, but not started, even if you check "Start UPnP and NAT-PMP service".