srch

06.09.2020 · I have had OpenWRT with OpenVPN running on a LinkSys WRT1900ACS for a while now, but recently OpenVPN has been unable to connect to my VPN provider (PIA). The strage thing I'm seeing is in "Interfaces" where the unmanag…

You could try connecting the Smart Hub DSL wall, and then Smart Hub LAN to Home Hub WAN; and you set your WAN interface in OpenWrt to DHCP. This ...

Hiii I keep getting this error with DS-Lite interface “error: Network device in not Present”. Attached below is the config/network & config ...

My problem is pretty simpel, completely stock openwrt with small ip configurations. i use LUCI to create a new interface, in this interface ...

Tun0 - Error: Network device is not present ... I updated my R7800 successfully and had an active working NordVPN connection for about 2 days.

Hello, After a few hours to operate without problems, connection with NCM stop working suddenly. I have a Huawei E3372 + Archer C7 v2 with ...

... given "Error: Network device is not present". I have OpenWrt 19.07.1 a router Archer C6 v2 root@OpenWrt:/etc/config# cat firewall config ...

May 03, 2019 · So I've bought a BT HomeHub 5a online and been trying to connect to my ISP (BT Infinity). Looking online, I found a guide by a person named 'Bill.L' and it was very useful. I followed the guide steps for '9.1 Quick PPPoE setup using DSL port for VDSL Connection' However, whenever I go and look at Network -> Interfaces, my WAN (labelled pppoe-wan') is listed as 'Error: Network device not found ...

Having a problem with ipv6 after setting up my wireless network. Anyone see something wrong? /etc/config/firewall config defaults option ...

interface says "device is not present" when bridging two wireless networks. Problem is in the title. i don't get a internet connection and i suspect this is the cause but i am not sure. i want to know anyways what the message means and what caused it. the interface that gives the message is PRIVATEWLAN. here below is my uci export. root@OpenWRT ...

Aug 18, 2020 · It means you cannot connect the VPN server due to connection timeout. Possible reasons: Incorrect VPN client configuration: Incorrect server address. Incorrect port. Incorrect protocol. Your connectivity is limited or restricted: Incorrect network configuration. The ISP or someone in the middle filters traffic.

[SOLVED] : TL;DR: When creating a bridge with wireless interface, wireless interface should not be added to the bridge on the network ...

Incorrect VPN client configuration: Incorrect server address; Incorrect port; Incorrect protocol · Your connectivity is limited or restricted:.

Mar 28, 2021 · This tutorial explains how to setup and configure OpenWrt for using a USB 3g/UMTS-modem for WAN connection using the older (and slower) ppp protocol. Many modern (and most LTE) usb modems provide qmi, mbim, ncm, rndis protocol for connection instead of legacy ppp protocol, they are faster and better, overall recommended.

23.09.2020 · Hello guys, Today I finally decided to flash my WRT 1900ACS and install OpenWRT. For the OpenVPN configuration, I followed every step of my VPN provider VPNUnlimited from the following manual: However, every time at the step for of my tun0 interface I get the error: Error: Network device is not present I have tried every possible solution that came to my mind …

Feb 16, 2020 · Please also share the content of /etc/config/wireless with keys redacted.

interface says "device is not present" when bridging two wireless networks. Problem is in the title. i don't get a internet connection and i suspect this is the cause but i am not sure. i want to know anyways what the message means and what caused it. the interface that gives the message is PRIVATEWLAN. here below is my uci export. root@OpenWRT ...

Jun 29, 2020 · Today, I tried to use the internet but realized it was not responding. Poking around I came up on the following which is my main concern because for the life ... Tun0 - Error: Network device is not present

14.05.2019 · [SOLVED] - Error: Network device is not present - BT HomeHub 5a. Installing and Using OpenWrt. bill888 May 4, 2019, 7:45pm #21. The HH5A is connected to DSLAM as both Line State and Data Rate show valid values. Can you post the 'wan' section from the /etc/config/network file so we can examine for errors? (eg. use ...

19.02.2020 · Please also share the content of /etc/config/wireless with keys redacted.

Hello guys, Today I finally decided to flash my WRT 1900ACS and install OpenWRT. For the OpenVPN configuration, I followed every step of my ...

30.06.2020 · Hi, I have Kong-OpenWRT installed on my R7800. ... Which in turn made the "Network device is not present" not there anymore ... ND 1056×392 60 KB. And the system log now shows. What command line can I execute to start the openvpn manually ? blackraiin June 30, 2020, 12:40pm #8.

May 04, 2019 · The HH5A is connected to DSLAM as both Line State and Data Rate show valid values. Can you post the 'wan' section from the /etc/config/network file so we can examine for errors? (eg. use WinSCP as described in section 10.2 of the guide) btw, it is dsl0.101 (begins with lower case DSL), not ds10.101. Update: I've amended the guide to make it clear to use lower-case 'DSL'.