srch

Jul 13, 2018 · This is LEDE Reboot 17.01.4 r3560-79f57e422d / LuCI lede-17.01 branch (git-17.290.79498-d3f0685) ( a stable release I believe) on a NETGEAR WNDR3700 V1. I set a static IP address and SAVE it but a reboot leaves me back where I started at default address (and with WiFi disabled if I enabled and saved that) This was a sys update from a OpenWRT ...

06.04.2019 · Backup and restore This article relies on the following: * Accessing OpenWrt WebUI * Accessing OpenWrt CLI Introduction * This how-to describes the method for using OpenWrt file-level backup/restore. * Follow Preserving packages to include user-removed/installed packages in your backup. * Follow Preserving configuration to determine whether to keep the settings.

14.07.2018 · Well the saving part is working . Samba is not,with a ps I get : 3201 root 2388 S /usr/sbin/smbd **-F** 3202 root 2468 S /usr/sbin/nmbd **-F** which I believe means samba is not running. I will have a look around and see if I can find a solution to that, if not I will start another thread. Thanks again

What ever combination of "save" "save & apply" OpenWRT does not save any change, I stay at "change counter > 0" stage. Further more, clicking on the counter I see all the changes and when I click to commit them it seems to work but at the end nothing is performed, all changes are still undone. reboot has no repair effect, even reloading the ...

Dec 05, 2021 · While upgrading OpenWrt firmware using web interface, you can utilize the “Keep settings” checkbox. It performs OpenWrt backup before upgrade and restores it after upgrade. If you do not precisely understand the button's use cases, uncheck “Keep Settings” every time you flash a new OpenWrt sysupgrade to your device, to not preserve settings.

A,B, or C? I Have the three version, and in my case B version do not admit OpenWrt 19.07. I will check out if A and C can't save settings, ...

or time zone for that matter. The password is saved however?? This is LEDE Reboot 17.01.4 r3560-79f57e422d / LuCI lede-17.01 branch ...

I had to go into /overlay/upper/usr/lib/opkg/ and manually delete some packages because opkg would not let me remove them.

Then lico goes to the page i clicked on however when i enter any details and press save or save and apply the changes are not saved.

OpenWrt 18.06.1 r7258-5eb055306f / LuCI openwrt-18.06 branch ... I can't do much with this as I'm not able to save any settings :roll_eyes:.

Hey, guys! I need help, I almost got UAP v2 working on openwrt! Last problem left, my settings are not saved after reboot.

What ever combination of "save" "save & apply" OpenWRT does not save any change, I stay at "change counter > 0" stage. Further more, clicking on the counter I see all the changes and when I click to commit them it seems to work but at the end nothing is performed, all changes are still undone. reboot has no repair effect, even reloading the ...

May 22, 2018 · Hi, I installed OpenWrt on NanoStation Loco M2. The configuration is not saved after the device is rebooted or powered off and on again. I will be very thankful to you if anyone can suggest me what to do.

09.11.2014 · Re: Not saving settings. Post. by garry.blott » Sun Nov 09, 2014 12:09 am. the message is on the bottom left hand of the browser, I don't think its a message form Gargoyle just info from the site. I actually re-flashed OpenWRT and configured all the settings, I then flashed with Gargoyle and it all worked, however if I look on the Status ...

Hi, I installed OpenWrt on NanoStation Loco M2. The configuration is not saved after the device is rebooted or powered off and on again.

Hello, I have successfully installed openwrt-18.06.8-ar71xx-tiny-tl-wr841-v8-squashfs-factory.bin on my router. Then I started to configure ...

Jul 22, 2018 · FS#1684 - 18.06.0-rc2 dos not save settings when applyed ramips/rt305x DIR-615-D2. D-Link DIR-615 D but using a D2 version. 18.06.0-rc2 but 17.01.5 is working fine! OpenWrt 18.06.0-rc2 r7141-e4d0ee5af5. I have a issue with Luci or maybe is issue with ramips/rt305x device’s but when i go to apply settings in the webgui and reboot my d-link it ...

Typically the reason for not saving any settings is that you have no writable overlay partition. Either the flash is so full that after ...

openwrt fails saving changesHelpful? Please support me on Patreon: https://www.patreon.com ...

May 31, 2018 · Hey all Im using the latest snapshot for bthh5a i have installed the uhttd and luci however when i click on anything it asks for logon credentials. Then lico goes to the page i clicked on however when i enter any details and press save or save and apply the changes are not saved. Have i missed a module or something when installing lucI ? thanks

22.07.2018 · FS#1684 - 18.06.0-rc2 dos not save settings when applyed ramips/rt305x DIR-615-D2. 18.06.0-rc2 but 17.01.5 is working fine! I have a issue with Luci or maybe is issue with ramips/rt305x device’s but when i go to apply settings in the webgui and reboot my d-link it goes back to the default openwrt settings however 17.01.5 is working fine no ...

22.05.2018 · Hi, I installed OpenWrt on NanoStation Loco M2. The configuration is not saved after the device is rebooted or powered off and on again. I will be very thankful to you if anyone can suggest me what to do. Thank you