srch

This brief video shows how to perform VLAN tagging and trunking at home using the inexpensive routers you already have or can find at bargain used prices. T...

so I read that I need to set a 802.1q TRUNK vlan that connect openwrt 15.05 x86 PC with switch openwrt 12.09 router. the switch router 'wr740n' has the following interfaces : eth0.1 which is vlan for LAN, eth1 wan eth0.3 that is a vlan for WAN3 and eth0.4 for WAN4. the table is

05.11.2021 · To use a VLAN you need at least 2 devices supporting VLAN features (as any route requires at least 2 points), which is usually advanced routers, any OpenWrt device, and any self-respecting PC or single-board computer (Windows, MacOS, Linux and BSDs support VLANs). OpenWrt supports IEEE 802.1Q and IEEE 802.1ad VLAN standards.

Jul 23, 2021 · The technology that enables an OpenWrt based device to be extended in terms of ports is VLAN . Notes Most devices only use one VLAN by default ( VLAN ID 1). The instructions that follow assume this is the case. Double check before proceeding.

Nov 05, 2021 · To use a VLAN you need at least 2 devices supporting VLAN features (as any route requires at least 2 points), which is usually advanced routers, any OpenWrt device, and any self-respecting PC or single-board computer (Windows, MacOS, Linux and BSDs support VLANs). OpenWrt supports IEEE 802.1Q and IEEE 802.1ad VLAN standards.

Aug 11, 2020 · A trunk port is tagged in all the VLANs. An access port is untagged in one VLAN and off in the others. Typically the CPU is also run as a trunk tagged in all the VLANs. This means you can attach it to networks with eth0.X, or you can leave it out of networks entirely.

This weekend I decided to finally upgrade the firmware on my Linksys WRT54GL wireless router. The whole reason I bought this router a few ...

You just need to configure the OpenWRT to use a trunk vlan port where the cable from the switch enters. Upvote 1

19.10.2014 · Home VLAN Trunking with OpenWRT and DDWRT My edge router is a Netgear WNDR3800 running OpenWRT which creates four VLANs for my domicile. I use Linksys e3000s running DD-WRT as managed switches distributing LANs where I want them to go.

23.07.2021 · So, imagine to have a 16 ports switch, we want to extend our router with 8 ports. We choose the first 8. So the ports 9-16 of the switch will retain the VID 1, and be untagged, with the VID 1 used also for management. Then we create the VID 100 to assign it to trunks or hybrid ports (a trunk is a port that is assigned to all the VLAN IDs, and ...

20.10.2014 · This brief video shows how to perform VLAN tagging and trunking at home using the inexpensive routers you already have or can find at bargain used prices. T...

openwrt x86 has only one NIC and I wish to connect with other device switch that has vlans (openwrt 12.09 tplink) this because with only one NIC i would not be able to has a LAN and WANs port. so I read that I need to set a 802.1q TRUNK vlan that connect openwrt 15.05 x86 PC with switch openwrt 12.09 router

Network Configuration. Here's what I'm trying to achieve with the below config: Tagged VLAN 3 (vid=3) on port 3 (virtual ...

A trunk port is tagged in all the VLANs. An access port is untagged in one VLAN and off in the others. Typically the CPU is also run as a trunk ...

Aug 16, 2021 · VLAN (Virtual LAN) Documentation User guide Network VLAN (Virtual LAN) ... If you want to contribute to the OpenWrt wiki, please post HERE in the forum or ask on IRC ...

22.08.2020 · So, as said before, the VLANs are "created" in the "main" router which is the PfSense. Everything is managed from there, I'd just like to set the OpenWrt to use WAN as trunk (for all the VLAN in/out traffic), set each LAN port to a different VLAN and set an IP to get access from outside the WAN interface.