srch

Apr 21, 2019 · Hi, I have installed OpenWrt 17.01.6 on my old D-LINK DIR-600 rev.B2. Lan & Wifi are working correctly however when I try to connect the WAN port to my ISP router (a Huawei HG8045H) as a DHCP client it does not seem to be able to get an IP. Here is my setup: When I use it as a dhcp client, udhcpc seems to send requests and that's it : daemon.notice netifd: wan (1888): udhcpc: sending discover ...

23.04.2019 · Hi, I have installed OpenWrt 17.01.6 on my old D-LINK DIR-600 rev.B2. Lan & Wifi are working correctly however when I try to connect the WAN port to my ISP router (a Huawei HG8045H) as a DHCP client it does not seem to be able to get an IP. Here is my setup: When I use it as a dhcp client, udhcpc seems to send requests and that's it : daemon.notice netifd: wan …

Replying to gerti-openwrt@bitart.com:. Using the same configuration I was using on a WRT54GL V1.1 on a WRT54G V2.0 I see the same problem, the WAN port does not pick up a DHCP address.

Could not get any connection through the router or from the router to the WAN/DMZ. Syslog shows errors DNSMASQ fails to start with "dnsmasq" unknown user or group. I added "dnsmasq" to both passwd and group (used same parms as network for entry in passwd). dnsmasq will now start, but connections problems persist.

You have right with WAN-Port. Since I tagged VLAN 1 an Lantiq Switch to "LAN", the WLAN don't work. I am not receive IP with WLAN. With LAN ...

Sep 08, 2018 · OpenWrt/LEDE DHCP IP issue. Installing and Using OpenWrt Network and Wireless Configuration. asterdeve.agi September 8, 2018, 10:21pm #1. Dear, All experts I am facing issue with OpenWRT/LEDE DHCP IP issue, I am unable to get DHCP IP, if I set static IP its worked fine but when I try to use DHCP it's not working I followed below solution but ...

I have a Comfast CF-WR650AC router, I installed the new version of OpenWRT 21.02, but the WAN port is not connecting properly, ...

Hi I have a netgear wndr3700v4 that has worked well with pppoe connected to an adsl modem in bridged mode. I have just gotten hfc nbn(in ...

Hi, I face a problem with my OpenWRT router. It works well for about 4 months. Yesterday I tried to block internet access to a range of IP ...

Hi, I have installed OpenWrt 17.01.6 on my old D-LINK DIR-600 rev.B2. Lan & Wifi are working correctly however when I try to connect the WAN ...

I have a Linksys router with OpenWRT 19.07 but the router is getting flakey, so I bought a new Asus RT-ACRH13 (AC1300) and flashed OpenWRT ...

17.07.2018 · FS#1664 - Unable to use wan port (dhcp or static ip is not working) Unable to use wan port on any new software version (last known working LEDE version is r3466-f6907dc). DHCP is not getting ip address. After setting up static ip address there is no network communication. There were 3675 commits between r3466-f6907dc and OpenWrt 18.06.0-rc1.

Dear, All experts I am facing issue with OpenWRT/LEDE DHCP IP issue, ... network 'lan' config zone option name 'wan' option input 'REJECT' ...

Installed LEDE Reboot 17.01.7 on Linksys wrt3200acm and problem is: If I set Wan protocol to DHCP client, I wont have internet until I call ...

Aug 14, 2016 · If I use the same hardware (just changing the USB Stick) with OpenWRT I instantly get my addresses (IP4 and 6). And if plugging in a Fritzbox I get addresses too. Tried changing "Block private" and "Block bogon" already, although should not have an effect, because the WAN IP I should be getting is 100.64.74.29/16.

Jul 17, 2018 · FS#1664 - Unable to use wan port (dhcp or static ip is not working) Device: Belkin F9K1115 v2. Software version: OpenWrt 18.06.0-rc1, LEDE after r3466-f6907dc. Unable to use wan port on any new software version (last known working LEDE version is r3466-f6907dc). DHCP is not getting ip address. After setting up static ip address there is no ...

Could not get any connection through the router or from the router to the WAN/DMZ. Syslog shows errors DNSMASQ fails to start with "dnsmasq" unknown user or group. I added "dnsmasq" to both passwd and group (used same parms as network for entry in passwd). dnsmasq will now start, but connections problems persist.

It is highly likely that there is an ip address conflict. Try changing the openwrt lan address to something else in a different subnet (for ...

08.09.2016 · Re: not getting IP via DHCP on WAN. « Reply #5 on: August 14, 2016, 12:19:57 pm ». I would: Try with IPv6 disabled to exclude that as an influence. Run tcpdump on the OPNsense WAN interface and look at the traces with Wireshark to see if where the DHCP protocol fails. Try a …

But the box is working, and I want to set it up for a friend as an ... This works fine as long as the cable at the WAN is not connected.