srch

or, if using OpenWrt SSH command line, you can use the command ping openwrt.org This should return “0% packet loss” if everything is alright with your Internet connection If your device has two (or more) ethernet ports, maybe OpenWrt and upstream WAN routers having conflicting IP address ranges.

25.11.2020 · Wed Nov 25 20:29:27 2020 user.info mwan3track [24520]: Lost 1 ping (s) on interface wan (eth0) 二、解决方案. 负载均衡 MWAN3 设置错误，是 MWAN3 这里的检测端口是否在线的 DNS 被墙了，3次 ping 失败就认为端口离线了，换成国内的 DNS 或者把检测开关关掉。. 在 网络 - 负载均衡 下修 WAN ...

upstream_router / \ other_machine openwrt_router 172.22.2.101 wan_IP: 172.22.2.100 I'm not able to ping OpenWRT router(172.22.2.100) from ...

Hello, i recently installed lede(or openwrt i'm not even sure at this point) on my archer c7 1750 v2 (OpenWrt SNAPSHOT r7066-060e1ecefa ...

I setup TPLINK WDR3600 with openwrt firmware. I have a modem (192.168.1.253) which I set it to bridge mode and I use a cable from this LAN to the WDR WAN (192.168.1.1). And another cable from WDR to pc. I can ping from inside WDR (I am connected via putty) but I can't from my browser (the internet conection doesn't work on pc). ifconfig:

Sep 12, 2021 · WAN interface protocols Protocol "ppp" (PPP over Modem) :!: The package ppp must be installed to use PPP. Name Type Required Default Description device file path yes (none) Modem device node username string no(?) (none) Username for PAP/CHAP authentication

Aug 11, 2018 · Select your WAN interface, in my case it is named pppoe-wan. For Queue Discipline, select cake and use piece_of_cake.qos queue setup script. For Link Layer Adaptation, the SQM guide on OpenWRT suggests the following (as at 2018-08-11): For VDSL - Choose Ethernet, and set per packet overhead to 8

27.02.2010 · I can confirm this issue on recent trunk. Ping flooding the remote WAN IP kills the router out of memory exhaustion. This is the case for ar231x & brcm47xx (16Mb RAM) devices without any running programs - daemons, only madwifi driver and static routing. This was tested on both jffs2/lzma & squasfs images.

... copy of OpenWrt 19.07 on my TP-Link Archer MR200 and I have a few issues with it. Port forwarding is not working I cannot ping WAN, ...

09.11.2021 · openwrt固件：. 无线路由器：WAN口*1，LAN口*4. ①、openwrt--网络--接口--LAN--物理设置：eth0（WAN，WAN6），eth1（LAN），WLAN（LAN）。. ②、所有LAN和WLAN的设备都能正常上网。. ③、WLAN的设备可以ping通LAN的设备（互ping都通）；. ④、LAN的设备之间ping不通。. 有哪位大佬 ...

03.02.2006 · The WAN still responded to ICMP ping. iptables -A input_rule -p icmp --icmp-type echo-request -j DROP -> This did work (WAN does NOT respond to a ICMP ping) and also allows me to still ping the NIC's on the LAN.

how to ping on both wan in openwrt as on mikrotik it's easy to setup it to give "/ip firewall route" on each others.

I setup TPLINK WDR3600 with openwrt firmware. I have a modem (192.168.1.253) which I set it to bridge mode and I use a cable from this LAN to the WDR WAN (192.168.1.1). And another cable from WDR to pc. I can ping from inside WDR (I am connected via putty) but I can't from my browser (the internet conection doesn't work on pc). ifconfig:

I've just spent a couple of hours this morning scouring Google and these forums, trying to work out how to turn on ICMP ECHO responses (WAN ping) ...

02.03.2009 · Yanira. 5 Mar 2009, 11:33. KillaB wrote: UCI is the preferred method, and adding the following to "/etc/config/firewall" works for me: config rule option _name ping option src wan option proto ICMP option target ACCEPT. Please also always post the UCI CLI commands: root@OpenWrt:~# uci add firewall rule root@OpenWrt:~# uci set firewall.@rule [-1 ...

Hi, thanks for reading. I get from my OpenWRT router's WAN interface (wan 192.168.178.72) the ping to my default gateway (192.168.178.1) but ...

As mentioned here Its not about mwan3 but lack of packet controls in OpenWrt on its own. There is nothing like that, that when you have ...

This question is not specific to OpenWrt, there are tons of resources on the internet about the pros and cons of filtering IGMP in general and ...

31.12.2020 · only ICMP-Echo-Request/ a.k.a. Ping is, see the default firewall rule. I would concur with @dizzy that especially for echo responses rate limiting is a better approach than blocking. Sure this slightly increases the attack surface on the router's wan side, but IMHO it also increases a link's debuggability by a lot.

Dec 27, 2020 · IPv4 ping being dropped should have no impact for a majority of consumers. Try not to drop connections solicited (an internal client pinging a external service) @meazz1 If you want to block ping, uncheck ONLY "Allow-Ping" and save. By Default the router will reply by telling the external source "I am not accepting pings".

12.09.2021 · PPP-based protocols negotiate IPv4 and IPv6 support when the link is established. These protocols require option ipv6 to be specified in the parent config interface wan section if IPv6 support is required. Further configuration can be given in the alias config interface wan6 section – see ipv6.

Hello All, Can anyone help me with OpenWrt network configuration My router can ping local hosts but not internet. Yet it is able to resolve domain to IP ...

29.10.2013 · With OpenWrt, it’s fairly easy to implement a simple watchdog that pings a public IP address every minute and triggers /etc/init.d/networking restart in case the ping fails a couple of times in a row. For a DSL connection, this means it will try to re-dial. This setup recovered a broken connection for me more than once :-).

In the OpenWrt admin web interface, go to Network → Diagnostics and Click on “ping” button or, if using OpenWrt SSH command line, you can use the command ping openwrt.org This should return “0% packet loss” if everything is alright with your Internet connection

I have seen an option in other firmwares like tomatousb to ignore ping requests from the WAN for added security. Is the recommended way to ...