srch

Now I need to whitelist couple of domains. How do I do that? ... Installing and Using OpenWrt Network and Wireless Configuration.

Depending on how comfortable and familiar you are with linux/openwrt and setting these things up this may be a lot of work. For domain based ...

Whitelist MAC Addresses (Macauth) for OpenWRT Written by Steve Hars Updated over a week ago Mac authentication lets you specify mac addresses which will not go through the splash page and can be automatically use the internet for free. Only local MAC authentication is supported.

Sorry for posting about openwrt on the lede forum, The openwrt forum is down but mentioned this forum as a possible source of info, ...

Assuming OpenWrt operates with a LAN and WAN zone a filter in the ... IP runs for example a blacklisted and whitelisted domain at once.

12.03.2020 · 自从编译 openwrt 时加入 Qbittorent 后，transmission 就出现了 403 错误。 403: Forbidden Unauthorized IP Address. Either disable the IP address whitelist or add your address to it. If you're editing settings.json, see the 'rpc-whitelist' and 'rpc-whitelist-enabled' entries. If you're still using ACLs, use a whitelist instead.

Adblock whitelist question I've been using the Adblock package and although I love the fact that it blocks ads for all my devices, I found it to be too disruptive sometimes and breaks a …

I'm pretty familiar with iptables, but this is the first time I've tried to do firewall/nat in OpenWRT where I needed to step out of the LuCi ...

Depending on how comfortable and familiar you are with linux/openwrt and setting these things up this may be a lot of work. For domain based whitelisting you should look into a proxy (squid for example). In the firewall redirect your brothers device packets (based on it's mac address is good) to the proxy port.

possible to whitelist for certain clients only? I setup OpenWRT with adblock a couple weeks ago and I'm browsing the interwebs in ad-free bliss. Only problem was my wife couldn't stream some TV shows on her phone. One was CBS All Access and the other was our local TV station. It would load a blank video feed and buffer for eternity.

Hi i am planning to install openwrt on my Archer C7. My usecase would be: I have a Synology and want to keep it available through the internet. I already have 2FA and limited login attempts in place but i also want to restrict devices to have access via the mac. So i would like to whitelist some MAC adresses.

16.12.2021 · If you want to contribute to the OpenWrt wiki, please post HERE in the forum or ask on IRC for access. Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International

In short, I'm interested in the different ways of creating an automatically-blacklist-everything specific-whitelist openwrt router, ...

Why do you use raw IPTABLES rules rather than FW3 which is built-in OpenWrt? It works by default and you can customize it to your needs. ask133:.

Firewall configuration /etc/config/firewall OpenWrt's firewall management application fw3 has three provisioning mechanisms Configuration ...

Hi, I have a router with OpenWRT, I need to setup a network blocked with only few accessible website in whitelist.

13.06.2021 · # 403: Forbidden Unauthorized IP Address. Either disable the IP address whitelist or add your address to it. If you're editing settings.json, see the 'rpc-whitelist' and 'rpc-whitelist-enabled' entries. If you're still using ACLs, use a whitelist instead. See the transmission-daemon manpage for details.

30.12.2010 · 403: Forbidden. Unauthorized IP Address. Either disable the IP address whitelist or add your address to it. If you're editing settings.json, see the 'rpc-whitelist' and 'rpc-whitelist-enabled' entries. If you're still using ACLs, use a whitelist instead. See the transmission-daemon manpage for details. The command I am using to pull up my ...

My Openwrt version is OpenWrt 19.07.7 r11306-c4a6851c72 and the router I have is an Archer A7 V5. My setup basically involves Nginx setup on a ...

09.05.2008 · Adding IPs to the Whitelist There are two ways to add addresses to this firewall ruleset. The first is to SSH into the OpenWRT router, edit the configuration file to add the appropriate rule, and then restarting the firewall service: Manually updating the whitelist ssh -l root 192.168.0.254 vim /etc/config/firewall /etc/init.d/S45firewall restart