srch

Sounds way too weird to me. I would think that when it connects to the Internet and you set the time zone setting it would keep time, or synchronize with one of ...

Is it possible that my Cloud Key Gen2 Plus has been compromised by this most recent ... You can correct this by SSHing into your CK and setting the time ...

Internet Traffic is only allowed for HTTP(s). I change the NTP Settings on the Cloud Key Interface to our internal NTP Server. But the Time Synchro didn't ...

Did you set the time correctly inf the controller GUI? Settings > Site. What firmware is your UCK/Controller running? Regards,. Glenn R.

Powering the UniFi Cloud Key Use an 802.3af-compliant switch, such as a UniFi PoE Switch, or a USB power source (not included). UniFi Switch ... step and set your access point up at a later time, click Skip. 4. On the Controller Access screen, create an admin account

I have a new cloud key just set up on 0.8.7 / 5.6.26 yesterday. I was looking at the logs and realized they were being timestamped using California time.

The Cloud Key updates its time via NTP on a regular basis, including during boot to adjust time after being powered down. If you don't have internet, ...

UniFi Cloud Key Configuration Login Instructions 1. Ensure that your host system is on the same Layer-2 network as the UniFi Cloud Key. 2. The UniFi Cloud Key is set to DHCP by default, so it will try to automatically obtain an IP address. Assign a specific IP address to the UniFi Cloud Key, or check the DHCP server for its IP address.

To use UniFi Protect, you will need:. A UniFi OS Console; One or more Protect cameras or security products; A compatible HDD for storing video footage, although you can set up Protect without one. To learn more about compatibility standards and view a list of incompatible HDDs, see UniFi - Hard drive compatibility and management.; The Cloud Key Gen2 Plus comes pre-installed with …

The Cloud Key Gen2 (UCK G2) is a next-generation UniFi OS Console that quadruples the power of its predecessor. Manage your UniFi system with the UCK G2. This slim but powerful UniFi OS Console can be set up and configured in minutes with UniFi's Bluetooth-powered mobile apps. Review real-time network and device insights concisely presented on the console's front panel …

09.01.2018 · Step 2 – Download the Unifi Controller Software. We are going to install the Unifi Controller to manage our access points. Now the Unifi Controller doesn’t have to be running al the time. So you can install it on your computer, configure your …

The UniFI AP's default back to 1969 if they can't get the right date. If changing the config.properties files on the controller does not solve the problem, set the time directly on the …

16.01.2020 · In general, I've been very happy with my Unifi cloud key for managing my Unifi network, but there have been 2 occasions over the past couple years where the cloud key has encountered unrecoverable failures.. In both cases, the cloud key's status LED was showing a white LED light instead of the normal blue. When this occurs I'm unable to login to the unifi …

Hi all, We have been having an issue with the time/date settings on our Ubiquiti Cloud Key where it is set to 2018.

Is there a way to set the NTP server for the CloudKey? ... CloudKey Gen2 Plus and Unifi Protect without internet possible?

21.12.2016 · Grab the IP for your Cloud Key and connect on port 22 using the username root and password ubnt. Once you've connected it's probably a good idea to change that password using the passwd command. Before we get started, stop the Unifi service. After this we need to remove the symlink to the existing keystore.

In researching the problem, however, I found the following configuration: root@UniFi-CloudKey:~# cat /etc/systemd/timesyncd.conf [Time] ...

Setting Up UniFi SDN 1. When the UniFi Setup Wizardscreen appears, select your country and timezone and click Next. 2. Select each of the devices you would like to configure and click Next. 3. If configuring a UniFi access point during setup, a Configure WiFiscreen will prompt you to create a wireless network name (SSID) and password.

Jan 16, 2020 · Login to the cloud key's website using your original credentials (now that it restored the backup) and change your ip address for the cloud key back to what it was originally. Your Unifi cloud key's LED light should now be back to blue from white, responsive, and working with your old configuration again.

16.01.2020 · This guide was done using an Unifi Cloud Key. If you have your Unifi Controller software in the cloud you can probably still use the custom configuration, but I do not know how to place it at the ...

I do have an ongoing issue with our UniFi Cloud Key Controller. The Controller does not have direct internet access, therefore I have configured all our 4 NTP Servers in the Settings -> Services - > NTP tab. However, the controller is still showing the wrong time while the date is correct. Settings -> Site -> Timezone is set correct.

Layer-2 network as the UniFi Cloud Key. 2. The UniFi Cloud Key is set to DHCP by default, so it will try to automatically obtain an IP address. Assign a specific IP address to the UniFi Cloud Key, or check the DHCP server for its IP address. Note: The default fallback IP address of the UniFi Cloud Key is 192.168.1.30. 3. Launch the web browser.

Layer-2 network as the UniFi Cloud Key. 2. The UniFi Cloud Key is set to DHCP by default, so it will try to automatically obtain an IP address. Assign a specific IP address to the UniFi Cloud Key, or check the DHCP server for its IP address. Note: The default fallback IP address of the UniFi Cloud Key is 192.168.1.30. 3. Launch the web browser.

The UniFI AP's default back to 1969 if they can't get the right date. If changing the config.properties files on the controller does not solve the problem, set the time directly on the AP. Published: Oct 19, 2017 · Last Updated: Oct 20, 2017

The time on the Cloud Key/in the Unifi controller is set via the internet. You have to set your correct Time Zone during configuration. If you want control over ...

Dec 21, 2016 · Grab the IP for your Cloud Key and connect on port 22 using the username root and password ubnt. Once you've connected it's probably a good idea to change that password using the passwd command. Before we get started, stop the Unifi service. After this we need to remove the symlink to the existing keystore.