srch

Feb 11, 2020 · Stop and Disable the job associated with the backup files you will be moving. Move backup files between extents as needed. Keeping in mind the details above about folder paths and vbm placement. In the Veeam Console, under Backup infrastructure > Scale-out Repositories, right-click on the affected SOBR, and select Rescan. Enable/run the job.

11.10.2021 · If you want to remove a performance extent from the scale-out backup repository, you first need to evacuate backups from this extent. When you evacuate backups, Veeam Backup & Replication moves backup files from the performance extent in question to other performance extents that belong to the same scale-out backup repository. You must put the performance …

Oct 11, 2021 · When you evacuate backups, Veeam Backup & Replication moves backup files from the performance extent in question to other performance extents that belong to the same scale-out backup repository. You must put the performance extent into the maintenance mode before you evacuate backups from it. For more information, see Switching to Maintenance Mode.

Feb 09, 2017 · Place the backup files to be imported in a temporary path. (e.g., if backup files are in D:\Backups, either copy or move them to D:\Backups-temp. A move is usually much faster.) Create a new simple backup repository that references this path (in our example, D:\Backups-temp). Re-scan the repository, and ensure all backups are imported.

Aug 08, 2018 · Can I just move alle the files for a backup from one folder to the other and do a rescan on both extents? Thanks! Edit: I forgot to mention: Veeam did split the Backup Copy onto both extents - just in a bad way in this case. Our 3 largest backups did end up on the same extent while the other extent has 1 large backup and a lot of small backups...

Veeam Community discussions and solutions for: Moving Existing Jobs to New ... What is the best way to move existing backup files to a new ...

Aug 26, 2015 · While there is not directly a UI task for moving your backups, the procedure itself is very simple. Just move the backups to the new location, repoint your backup job to the new location through the backup wizard and the next time the backup runs, it will detect your backup files again and you are good to go. Read the next chapter:

15.11.2015 · Re: Move a job's data from 1 extent to another in SOBR. OK should have looked a bit further. Turns out that since the attribute is per-VM, and not per-JOB, Veeam distributed the first FULL backups actoss the extents. so I guess if I just moved the VBK and VIB files to the job directory on another extend and rescan I would be fine?

08.02.2013 · This method uses a feature built-in to Veeam Backup & Replication that seamlessly switches between repositories when old and new repositories contain the same backup files for the job (VBM, VBK, VIB, VRB). When the new repository is selected within the job, Veeam Backup & Replication will check if the backup files in the selected repository match the existing …

Create a dummy repository · place the existing backup files in there · rescan the repository · add the dummy repository to the existing scale-out ...

So i moved the Files from one VM to the Folder of the same Job on another extent and made a Rescan. But now the Backup Copy job is still ...

In this case, backup files will be moved to other extents of the scale-out backup repository, and the backup chain will remain consistent. If ...

Stop and Disable the job associated with the backup files you will be moving. · Move backup files between extents as needed. · In the Veeam ...

Method A: Same Job, New Backup location · Disable the backup job(s) planned to be moved; this will prevent additional restore points from being ...

Feb 08, 2013 · Create a new repository for the new location where backup files will be located. Manually move the backup files to the new repository path. You must include the metadata file (.vbm), full backup files (.vbk), and any needed incremental files (.vib or .vrb). Note: It is recommended to move all backup files, but you may omit incremental files if ...

When you evacuate backups, Veeam Backup & Replication moves backup files from the performance extent in question to other performance ...

11.02.2020 · Stop and Disable the job associated with the backup files you will be moving. Move backup files between extents as needed. Keeping in mind the details above about folder paths and vbm placement. In the Veeam Console, under Backup infrastructure > Scale-out Repositories, right-click on the affected SOBR, and select Rescan. Enable/run the job.

07.02.2019 · Problem evacuating extent in SOBR. We are running VBR 9.5.0.1922. We are having problems evacuating an extent in preparation for replacing the extent with different storage. We have moved some files manually between extents but we have not knowingly deleted any backup files. There are no backup files left in the extent that is in maintenance mode.

09.02.2017 · Evacuate the extent. Veeam will redistribute the backup files to other extents in the SOBR. If you did not map the original job in step 4, do so now. If redistribution of files is not desired or necessary, you can simply copy the folder containing VBM and backup files to an existing extent. Rename both path and VBM to ensure import, and re-scan ...

Create the SOBR and add the relevant repositories as extents. Within the creation process Veeam will inform via confirmation prompt that “Jobs ...

When you remove a performance extent, Veeam Backup & Replication puts the ... backup files will be moved to other performance extents of the ...

Veeam Community discussions and solutions for: Moving some Backups ... However the distribution of the Files/Backups is less than optimal.