srch

19.07.2011 · Expand the sections below for instructions to complete each troubleshooting step. 1. Make sure the Veeam vPower NFS Service is running on the Mount Server. 2. Check if another NFS Server software is locking port 111 on the Mount Server. 3. Remove previously used vPower NFS Datastores marked as (Invalid) in the vSphere Environment. 4.

18.03.2021 · If you plan to use a devoted backup proxy server or cache repository, make sure these components are added in Backup Infrastructure. To add an NFS file share: Launch the New File Share wizard. Specify the path to the NFS file share and access credentials. Specify advanced NFS file share settings. Specify file share processing settings.

12.02.2018 · VMware vSphere versions that are no longer compatible with the most recent version of Veeam Backup & Replication can be found in the Previously Supported table found at the bottom of this article. Note: There is a known issue where a Veeam Proxy running on a VM may become listed as (invalid) in vSphere.

When Veeam Backup & Replication processes VM data in the Network mode, it uses VMware VDDK to communicate with the ESXi host. This produces ...

Veeam Community discussions and solutions for: vPower NFS version of Veeam Backup & Replication.

If the environment you are working with is running a previous version or does not have a vCenter, consult VMware documentation for creating an ...

Currently, Veeam Backup & Replication v10 supports filers presenting capacity via NFS share using protocol version v3.0 and v4.1 only. The ...

Veeam supports NFS versions 3.0 and 4.1 (just like vSphere). Thanks! Top. danswartz: Expert ...

06.10.2011 · Right-click the host and in the context menu under Storage, select New Datastore Step 4 For datastore type select NFS Step 5 For NFS version select NFS 3 Step 6 Enter the information gathered in Stage 1 of this article. Step 7 Review details and click Finish

Mar 18, 2021 · If you plan to use a devoted backup proxy server or cache repository, make sure these components are added in Backup Infrastructure. To add an NFS file share: Launch the New File Share wizard. Specify the path to the NFS file share and access credentials. Specify advanced NFS file share settings. Specify file share processing settings.

The vPower technology enables the following features: Recovery verification Instant Recovery Instant Disk Recovery Staged restore...

Introduction

Dec 22, 2021 · NFS file share must run NFS protocol version 3 or 4.1. Anonymous or AD/Kerberos authentication is not supported for access to file shares through NFS. In NFS settings of the source file share, you must explicitly specify what servers will have access to the file share. SMB file share must run on SMB version 1.x, 2.x or 3.x.

When you perform restore from storage snapshot on NetApp storage systems working over the NFS protocol, Veeam Backup & Replication...

Jun 08, 2021 · Veeam Backup & Replication uses the highest NFS protocol version supported by the gateway and the repository. Note that the suffix indicating the NFS version in the NFS share properties may not be displayed correctly, this is a known issue.

Oct 10, 2013 · Veeam NFS on version 7. I have just installed v 7.0 on a Windows 2008R2 system that also runs my vSphere. I cannot get the VeeamBackup_SERVERNAME NFS share mounted. I have followed the KB articles I have found here to no avail, they all seem for version 5.x or 6.x - nothing for 7.x. My one initial problem was that Windows Services for NFS was ...

NFS Backup Repository Deployment To communicate with an NFS backup ... Veeam Backup & Replication uses the highest NFS protocol version ...

22.12.2021 · The Microsoft Windows server that acts as an NFS file share requires network ports listed below and also ports listed in the NFS Repository Connections. 1 This range of ports applies to newly installed Veeam Backup & Replication starting from version 10.0, without upgrade from previous versions.

3 This version is supported starting from Veeam Backup & Replication 11a (build 11.0.1.1261) with Cumulative Patch P20211211. Software During setup, the system configuration check is performed to determine if all prerequisite software is available on the machine where you plan to install Veeam Backup & Replication .

Veeam introduced in Backup and Replication version 9 a new transport mode called Direct NFS. It's similar to Direct SAN transport mode where ...

Before you add an NFS file share to the inventory of the virtual infrastructure, check the following prerequisites: The file share...

30.09.2021 · NFS file share must run NFS protocol version 3 or 4.1. Anonymous or AD/Kerberos authentication is not supported for access to file shares through NFS. In NFS settings of the source file share, you must explicitly specify what servers will have access to the file share. SMB file share must run on SMB version 1.x, 2.x or 3.x.

13.10.2013 · Veeam NFS on version 7. I have just installed v 7.0 on a Windows 2008R2 system that also runs my vSphere. I cannot get the VeeamBackup_SERVERNAME NFS share mounted. I have followed the KB articles I have found here to no avail, they all seem for version 5.x or 6.x - nothing for 7.x. My one initial problem was that Windows Services for NFS was ...

08.06.2021 · Veeam Backup & Replication uses the highest NFS protocol version supported by the gateway and the repository. Note that the suffix indicating the NFS version in the NFS share properties may not be displayed correctly, this is a known issue. Tip