srch

28.08.2015 · No new files to backup per job settings. I've created a one-off 'Files to Tape' job to archive off 5TB of old data from 4 servers so I can remove it from disk. Three of the servers have Veeam agents on them, and the fourth is Veeam itself. I added them to the job by selecting each server in the dropdown list of agents, then picked the entire D ...

23.03.2010 · Job has never taken more than 3 seconds to run always success. 0.0 transferred. Always note No new files to backup per job setting. created a second job to backup the files in the backups folder and it is running and transferring info. The Veeam server with the tape drive has no jobs that backup to the repository but other Veeam servers do.

If there is no new files on disks, nothing is to be written on tape. If there are new files, I would double-check "source" in the job wizard and ...

Disable the Use hardware compression when available check box. Usually image-level backups of VMs are produced by Veeam Backup & Replication by ...

Veeam Community discussions and solutions for: Backup to tape ... tasks 26.08.2016 23:45:40 :: No new files to backup per job settings ...

Jun 08, 2013 · No new files to backup per job settings. I've created a one-off 'Files to Tape' job to archive off 5TB of old data from 4 servers so I can remove it from disk. Three of the servers have Veeam agents on them, and the fourth is Veeam itself. I added them to the job by selecting each server in the dropdown list of agents, then picked the entire D ...

27.04.2021 · You can instruct Veeam Backup & Replication to create per-machine backup files in the backup repository. In this case, the backup job will use a separate write stream for every VM in the job, and store data of every VM to a separate backup file. Resources of the storage device will be used more efficiently, and the job performance may increase.

Veeam Community discussions and solutions for: Tape "logic" means no data ... and 'No new files to backup per job settings' session message.

Veeam Community discussions and solutions for: "No backup files found" since ... files found" and "No new files to backup per job settings".

Mar 24, 2010 · Always note No new files to backup per job setting. created a second job to backup the files in the backups folder and it is running and transferring info. The Veeam server with the tape drive has no jobs that backup to the repository but other Veeam servers do. larry wrote: ran it ten times, take a couple of seconds.

03.05.2021 · Open advanced settings of the job. On the Notifications tab, select the Send email notifications to the following recipients check box. In the field below, enter an email address to which a notification must be sent. You can enter several email addresses separated with a semicolon. Note. If you specify the same email recipient in both job ...

Apr 27, 2021 · You can instruct Veeam Backup & Replication to create per-machine backup files in the backup repository. In this case, the backup job will use a separate write stream for every VM in the job, and store data of every VM to a separate backup file. Resources of the storage device will be used more efficiently, and the job performance may increase.

Apr 20, 2013 · Re: no new files to backup per job settings (tape) Post. by Shestakov » Sun Jul 16, 2017 4:50 pm. this post. If there is no new files on disks, nothing is to be written on tape. If there are new files, I would double-check "source" in the job wizard and then right-click on the tape job and manually run weekly GFS.

01.10.2021 · Click Advanced to configure additional settings for the backup repository:; For storage systems using a fixed block size, select the Align backup file data blocks check box. Veeam Backup & Replication will align VM data saved to a backup file at a 4 KB block boundary.; When you enable compression for a backup job, Veeam Backup & Replication compresses VM …

Jul 04, 2019 · A tape job finishes with the Success status, but the backup files of a source job(s) are not copied. In the tape job statistics, you can find the "No backup files found"/"No new files f

That's by design. Backups not associated with existing jobs are skipped from processing. In order to archive those backups you should either ...

Veeam Community discussions and solutions for: No new files to backup per job settings of Tape.

It just says "No new files to backup per job settings." I haven't changed anything. Any ideas or am I imagining things?

Tape job does not copy source backup files and finishes with "No backup files found"/"No new files found" message ; KB ID: 2975 ; Product: Veeam ...

No new files to backup per job settings * 5/11/2018 12:15:28 AM :: Synthesized full backup was not created for 5/11/2018: there are no new ...

Oct 09, 2013 · As an individual log file grows larger than the maximum size a new generation of log files is created. This registry setting controls the maximum number of generations of log files to be retained. Example: Svc.VeeamBackup_1.log, Svc.VeeamBackup_2.log, Svc.VeeamBackup_3.log, etc. Key Location: HKLM\SOFTWARE\Veeam\Veeam Backup and Replication