Dec 09, 2013 · I'm using ZFS on OSX and I've zpool which is active and online: NAME SIZE ALLOC FREE CAP DEDUP HEALTH ALTROOT WD_1TB 931G 280G 651G 30% 1.00x ONLINE - but I can't actually mount it. $ sudo zfs mount WD_1TB cannot open 'WD_1TB': pool I/O is currently suspended cannot open 'WD_1TB': pool I/O is currently suspended
11.12.2013 · The pool's I/O is suspended because ZFS is not seeing your disk there at all. If you have used the symlink trick to point ZFS to the new location of the disk you disconnected and reconnected, then you can issue zpool clear -F WD_1TB. If it still does not see the disk it will continue to tell you the I/O is suspended.
Follow the procedures in Replacing or Repairing a Damaged Device. A pool might be SUSPENDED if device connectivity is compromised. A SUSPENDED pool remains in ...
29.11.2019 · After #740 the pool imports but any operation results in zpool command hanging or reporting "pool I/O is currently suspended" $ sudo zpool offline zpool media-6ACB9174-C22B-F943-95CB-C46AEE8C90A2 cannot offline media-6ACB9174-C22B-F943-9...
After a device is reattached to the system, ZFS might or might not automatically detect its availability. If the pool was previously UNAVAIL or SUSPENDED , or the system was rebooted as part of the attach procedure, then ZFS automatically rescans all devices when it tries to open the pool.
02.10.2017 · Would really prefer zpool export -F for suspended pools, but zpool clear would be sufficient if it would work. EDIT: I should add that the current state is still an improvement over 0.6.5.x, as a system in this state can run zpool/zfs commands on other pools, as well as a zpool list or zpool status affecting the suspended pool, which was not always the case when this …
May 11, 2020 · The device failed (probably bad cable/connection, because the disk reads fine on another machine). But how do I --force GNU/Linux to forget the device? $ zpool status pool: freenetpool state: SUSPENDED status: One or more devices are faulted in response to IO failures. action: Make sure the affected devices are connected, then run 'zpool clear ...
Dec 11, 2013 · The pool's I/O is suspended because ZFS is not seeing your disk there at all. If you have used the symlink trick to point ZFS to the new location of the disk you disconnected and reconnected, then you can issue zpool clear -F WD_1TB. If it still does not see the disk it will continue to tell you the I/O is suspended.
Apr 23, 2015 · do not mix zones and zpools conceptsYour zones are on top of zpools and these zpools are in suspended. first fix the zpool: Check status zpool status <zpool-name> then depending on the output take the proper action to fix it. Ensure that your devices disks that are part of the zpools are there. Check Oracle Documentation here Share
I originally had this zpool on a machine with other zpools and apps. However, once a zpool becomes suspended, a reboot is required to gain I/O access again. I've since moved this zpool to a dedicated machine that does nothing but receive backups from other machines. Hardware setup: SuperMicro SC826 chassis with a SAS2 expanding backplane
09.12.2013 · I'm using ZFS on OSX and I've zpool which is active and online: NAME SIZE ALLOC FREE CAP DEDUP HEALTH ALTROOT WD_1TB 931G 280G 651G 30% 1.00x ONLINE - but I can't actually mount it. $ sudo zfs mount WD_1TB cannot open 'WD_1TB': pool I/O is currently suspended cannot open 'WD_1TB': pool I/O is currently suspended
11.05.2020 · The device failed (probably bad cable/connection, because the disk reads fine on another machine). But how do I --force GNU/Linux to forget the device? $ zpool status pool: freenetpool state: SUSPENDED status: One or more devices are faulted in response to IO failures. action: Make sure the affected devices are connected, then run 'zpool clear ...
13.11.2014 · Hi, I am trying disk replacement from a single disk zpool and it results to suspended IO and does not allow me to destroy the zpool. Steps to reproduce: create a zpool with single disk (zpool create zp1 /dev/sda) remove the disk zpool st...
I originally had this zpool on a machine with other zpools and apps. However, once a zpool becomes suspended, a reboot is required to gain I/O access again. I've since moved this zpool to a dedicated machine that does nothing but receive backups from other machines. Hardware setup: SuperMicro SC826 chassis with a SAS2 expanding backplane
Jul 10, 2021 · zpool: pool I/O is currently suspended Tried zpool clear -nF external and zpool clear external Just sits blankly for hours The data was not irreplaceable so I gave up and just tried zpool destroy -f external but nothing happens. Rebooting does nothing as well. The drive has some jails and data on it using iocage.