srch

Firewall team has confirmed that the ports are wide open and also the port 3389 is listening inside the server.But when I did the portquery from the citrix jump server (10.100.0.30) to the destination 10.0.0.25 , the result shows as TCP port 3389 is filtered.I had a quick screen share with the person who implemented the firewall change to ...

22.01.2019 · Routers must have marked routes to the networks you want to visit. These networks can be configured statically or learned by routing protocols, such as RIPv2. To configure RIP v2 on your routers do this: R1 (config)#router rip. R1 (config-router)#network 10.1.1.0. R1 (config-router)#network 192.168.1.0.

Solved: I'm a student at a college and I keep getting issues in doing the ping and it works when i ping the devices in same switch but ı ...

Solved: Hi, I am trying to ping the server from PC3 and PC4 only (green highlighted) however, I keep getting destination host unreachable.

Solved: Hi everyone: I have a school project and when I ping computer PC-A to PC-C and vice versa, I get Destination host Unreachable. Can anyone help?

I am currently trying to ping connectivity to all devices and am having an extremely hard time. I have attached the packet tracer info.

When the host cannot complete the IP to MAC mapping it will use "Destination host unreachable". If you were to add a static ARP cache entry for 20.1.1.3 the message would change to "Request timed out"

23.03.2017 · Destination Host Unreachable So I've set up a small lab in GNS3, and I don't know why I can't ping to my default gateway as I've seem to keep getting destination host unreachable. I've narrowed down the problem to the switch I'm using, because without the switch I know I can ping the default gateway just fine.

Dec 31, 2019 · Destination Host Unreachable. Hi, I am trying to ping the server from PC3 and PC4 only (green highlighted) however, I keep getting destination host unreachable. I am not sure what's incorrect. Please advise - I have attached the packet tracer file within the zip folder as it does not allow me to attach the .pkt file.

Nat/routing problem (Destination host unreachable). Hi, i was following learn tech "Connecting cisco router to DSL Modem with SP ...

For example PC0 to PC2 it gives me the "Destination host is unreachable" error and doesnt send the ping. However when I try to ping a pc on ...

... once I'm finished with my setup I try to ping the Loopback address on a Router from PC1and PC2 and I keep getting "Destination host unreachable" message.

Jan 22, 2019 · Routers must have marked routes to the networks you want to visit. These networks can be configured statically or learned by routing protocols, such as RIPv2. To configure RIP v2 on your routers do this: R1 (config)#router rip. R1 (config-router)#network 10.1.1.0. R1 (config-router)#network 192.168.1.0.

Dec 29, 2006 · My requests either time out or I get destination host unreachable back from the router. I have a VPN tunnel setup between my lab router and my PIX at home going through the cable internet. 172.16.0.0 is my router subnet and 172.16.1.0 is my PIX home subnet. Here's my config: interface FastEthernet0/0.1. description Voice Network.

30.12.2019 · Destination Host Unreachable. Hi, I am trying to ping the server from PC3 and PC4 only (green highlighted) however, I keep getting destination host unreachable. I am not sure what's incorrect. Please advise - I have attached the packet tracer file within the zip folder as it does not allow me to attach the .pkt file.

Cisco challenge - Destination host unreachable ... c1 to c2 and ping c2 to VBox however, I'm getting destionation host is unreachable error.

Mar 23, 2017 · Destination Host Unreachable So I've set up a small lab in GNS3, and I don't know why I can't ping to my default gateway as I've seem to keep getting destination host unreachable. I've narrowed down the problem to the switch I'm using, because without the switch I know I can ping the default gateway just fine.

11.12.2020 · I tried to build a simple network in Packet Tracer and I get "Destination host unreachable" when I try pinging a PC from another network. Pinging PCs from the same network works. When I use tracert to a PC from another network it …

Apr 23, 2018 · Destination Host Unreachable issue in Packet Tracer I'm a student at a college and I keep getting issues in doing the ping and it always tell me that the destination host is unreachable. I would to get some help on what's wrong with the configuration.

ICMP Unreachables are normally limited to no more than one every one-half second per input interface, but this can be changed by using the ip icmp rate-limit ...

That error means that you have misconfigured to network mask on the PCs. The PCs on one network think the PCs on the other network are on the same network as ...

When the host cannot complete the IP to MAC mapping it will use "Destination host unreachable". If you were to add a static ARP cache entry for 20.1.1.3 …