srch

If they are being block wouldn't that mean I am unable to ping those IP addresses yet after running those commands on a WRT54GL DD-WRT ...

On this page of the DD-WRT wiki, it says "Under Website Blocking by URL Address, enter in the domain name(s) you wish to block (if any)." This, in addition to posts on the DD-WRT forums, gives me the impression that you can only block domains under Access Restrictions in the DD-WRT setup.

You can create rules that govern access by individual IP or MAC address, IP address range, time-of-day, traffic type, URL and keywords, etc. You ...

Depreciated, See Access Restrictions [] Global Blacklisting per MAIf you have a lot of DD-WRT routers, then denying of access for abusing users through the web interface of each router can be time consuming.

Apr 11, 2013 · There are a set of IP addresses you can block so that you stream directly from youtube instead of going through your ISP's slow servers. I put in any of those above commands into the dd-wrt control panel but doesn't actually block anything. I even put in IP's for other sites and such and still am able to connect.

[edit] Global Blacklisting per MAC. If you have a lot of DD-WRT routers, then denying of access for abusing users through the web interface of ...

19.02.2015 · To restrict access to these name the service HTTPS, select TCP for protocol and the Port range 443~443. Press Add to add the service, then Save followed by Apply Settings. Close the dialog and check the Blocked Services field. The DD-WRT router is now configured to block all P2P Protocols and HTTPS.

-s <camera1_ip>: Specifies which source IP address to which the rule should be applied (eg. -s 192.168.1.240).-o vlan2: Specifies that the rule only applies to traffic that is being sent out through vlan2. Vlan2 is the WAN interface in dd-wrt, by default.

13.04.2021 · Certain streaming services function more reliably if you block specific IP addresses on your router. This guide will show you how to block specific IP addresses on DD-WRT routers.. To block specific IP addresses on your DD-WRT router, you will need to use static routing rules to ensure your network traffic does not flow through the IP addresses you specify.

Which would DROP all packets destined to the given IP. Useful to block access to whatnot. If you want to log the ...

I just wanted to block my IP cameras from accessing the external network, ... Does anyone know the best way to do this with DD-WRT?

I was re-reading my question after posting to make sure it was accurate and came up with an idea... It worked. I adjusted the DD-WRT's ...

Here's how to Block specific IP addresses on DD-WRT router. Hit https://www.linkev.com/?a_aid=expssour ...

1. Type the router's default IP on the address bar of your browser. Select the Set-Up tab. · 2. Select Advanced Routing from the tabs across the ...

Depreciated, See Access Restrictions [] Global Blacklisting per MAIf you have a lot of DD-WRT routers, then denying of access for abusing users through the web interface of each router can be time consuming.

Connect IPTV box using LAN cable to one of the LAN ports of the router Note: in AP mode, LAN cable to gateway/modem and LAN cable to IPTV box must be on the switch ports of the dd-wrt router and not on the WAN port, even if "assign WAN port to switch" is enabled. Tested on Linksys EA2700 (build 38581), Netgear R7000, Netgear R7000P.

If you assigned your router a different local IP address, use that instead. 4. In the web interface, click on the Services tab. Enter your DD-WRT router username and password, if prompted. 5. Scroll down to the 'DNSMasq' section. Make sure that DNSMasq bullet and Local DNS bullets are set to 'Enable' that no other DNSMasq options are set. 6.

I need complete block ip 159.153.76.33 in firewall. ... I checked wiki ddwrt but I dont understand which iptables I need put.

Apr 13, 2021 · This guide will show you how to block specific IP addresses on DD-WRT routers. To block specific IP addresses on your DD-WRT router, you will need to use static routing rules to ensure your network traffic does not flow through the IP addresses you specify. Jump to… 1. Sign in to your router admin panel 2. Change your router network settings

Unfortunately, the impression I get (from the DD-WRT forums) is that you can only block domains under Access Restrictions in the DD-WRT setup. I've decided instead to set up a dedicated proxy server with DansGuardian installed on it, which will allow me a fine level of control, and block any requests that don't go through the proxy on the router using iptables in OpenWrt.

20.04.2013 · There are a set of IP addresses you can block so that you stream directly from youtube instead of going through your ISP's slow servers. I put in any of those above commands into the dd-wrt control panel but doesn't actually block anything. I even put in IP's for other sites and such and still am able to connect.

Feb 19, 2015 · To restrict access to these name the service HTTPS, select TCP for protocol and the Port range 443~443. Press Add to add the service, then Save followed by Apply Settings. Close the dialog and check the Blocked Services field. The DD-WRT router is now configured to block all P2P Protocols and HTTPS.

You are here: DD-WRT wiki mainpage / Scripting / SSH/Telnet & The CLI / iptables Iptables is a powerful administration tool for IPv4 packet filtering and NAT. It is used to set up, maintain, and inspect the tables of IP packet filter rules in the Linux kernel.