I am using Linux oess (CentOS). I am working on a VM: In the terminal, I'm trying to: ping 8.8.8.8 to see my connectivity. It says: Network is unreachable Then I typed: ifconfig: inet addr: 192.168.56.101 Then: sudo /sbin/route add -net 0.0.0.0 gw 192.168.56.101 eth0 Now I'm doing the same ping and it says: Destination host is unreachable
27.12.2017 · Ubuntu Linux, private network with three devices: laptop, cdev, and edev. All three connected to a switch that shows all active. Ping returns message: Connect: Network is unreachable Wireshark shows that device cdev is sending messages I edited /etc/host such that I left the first few lines unchanged as shown here
Dec 24, 2012 · my os is Centos 6.3 with 2.6.32-279.19.1.el6.x86_64 linux kernel. I've config it to enable ipv6, but when ping , network is unreachable. please help.
Aug 10, 2014 · Destination host unreachable. Destination host unreachable. Ping statistics for 4.2.2.2: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\example> When you ping to an IP address in a different network, ping packets reach default gateway. Your default gateway sends the packet to remote gateway. So ping packet finally reaches the remote ...
02.10.2014 · gonvaled@pegasus ~ » ping archive.ubuntu.com connect: Network is unreachable Traceroute is also failing: gonvaled@pegasus ~ » traceroute archive.ubuntu.com traceroute to archive.ubuntu.com (91.189.88.149), 30 hops max, 60 byte packets connect: Network is unreachable This is my network config (nothing out of the ordinary!):
Dec 27, 2017 · Ubuntu Linux, private network with three devices: laptop, cdev, and edev. All three connected to a switch that shows all active. Ping returns message: Connect: Network is unreachable Wireshark shows that device cdev is sending messages I edited /etc/host such that I left the first few lines unchanged as shown here
I am using Linux oess (CentOS). I am working on a VM: In the terminal, I'm trying to: ping 8.8.8.8 to see my connectivity. It says: Network is unreachable Then I typed: ifconfig: inet addr: 192.168.56.101 Then: sudo /sbin/route add -net 0.0.0.0 gw 192.168.56.101 eth0 Now I'm doing the same ping and it says: Destination host is unreachable
OpenSuSE: ping: unknown host, and connect: network is unreachable. WAIT: Read the whole post before applying any changes. You will know why once you’re done! Note: Seems like it’s kind of common for SuSE, but you can easily modify the few specific lines to work with your distro. Most commands are common Linux stuff.
20.07.2009 · Cannot ping vm host - destination host unreachable. 639423 Member Posts: 20. Jul 20, 2009 9:06PM edited Jul 23, 2009 7:27AM in Oracle Linux. Hi I'm a newbie to vmware. I am setting it up for oracle rac usage and am following an official guide (the one from vincent chan). I have set up 2 x Linux Servers (Oracle Enterprise Linux 4), ...
Disconnect the power cables and Ethernet cables from the modem, router, and PC. Clean the cables, and reconnect them. Power on the devices after two minutes.
Show activity on this post. The problem is ,you need to set your default gateway. 1)Take terminal. 2)sudo su. 3)Type in. $ route add default gw (eg:192.168.136.1) eth0. 4)sometimes you will be able to ping (ping 8.8.8.8) but no internet connection in the browser,then. 5)go to 'nano /etc/resolv.conf'. 6)Add.
When I attempt to ping google's dns or any outside the network I get connect: Network is unreachable? I can't update either which I put down to this I …
10.08.2014 · The error message " Destination Host Unreachable ", during a ping test, tells that the ping request from our computer cannot find the route to the destination IP address ( destination host ). It means the packet sent from your computer reached the destination network successfully but the remote gateway failed to find the destination host.
22.10.2020 · Linux 下使用 ping 出现 destination is unreachable 的问题可能性 angou6476的博客 64 ping 时出现request time out和 destination is unreachable request time out是指icmp包发出后，长时间没有回应，所以会产生request time out。 一般是 ping 了一台 网络 中不存在的主机。 destination is unreachable 或 destination port unreachable 一般是收到了目标主... Destination …
How to Add the Correct Gateway Address for a Destination Host · Select Settings > Network and Internet > Network Connections. · Right-click the relevant Local ...
Oct 23, 2019 · i have successfully install OpenSSH on a Windows machine that mean i can connect from linux to windows with: ssh username@ipAdresse i've tried using a lot of version of ansible (2.6, 2.7.12, 2.7.14, 2.8.5 and 2.8.6) and i always test if i can ping an other Linux machine with this line(it work): ansible linux -m ping There is my hosts file
22.10.2019 · i have successfully install OpenSSH on a Windows machine that mean i can connect from linux to windows with: ssh username@ipAdresse i've tried using a lot of version of ansible (2.6, 2.7.12, 2.7.14, 2.8.5 and 2.8.6) and i always test if i can ping an other Linux machine with this line(it work): ansible linux -m ping There is my hosts file