srch

(OpenWRT or iproute2, macvlan???) ... I can just assign it to WAN firewall zone (OpenWRT thingie, not so important) for ez profit.

21.01.2022 · Setup MACVLAN interface in OpenWrt. Here the MACVLAN interface will be created which is a virtual interface bridged to current LAN interface. This interface will later be used by Docker and PiHole. Look for the config interface 'lan' section and note down the device from the option device line.

[OpenWrt-Devel] [PATCH] macvlan interfaces with uci ... This patch adds support for macvlan interfaces to uci. ... dependencies: kmod-macvlan, ip

Installing and Using OpenWrt Network and Wireless Configuration ... After installation of the macvlan kernel module, is a /etc/network ...

22.09.2021 · Docker macvlan network on OpenWRT x86. Hi, I’m trying to use OpenWRT x86/64 as a Docker host to run pihole attached to the LAN network of OpenWRT. I have done this before with an Ubuntu host where pihole is a docker container, running on the Ubuntu host connected to bridged Ethernet network. I had to do the macvlan workaround so that the ...

Jan 09, 2022 · kmod-macvlan Version: see kernel for details Description: A kernel module which allows one to create virtual interfaces that\\ map packets to or from specific MAC addresses to a particular interface\\ \\ Installed size: 11kB Dependencies: kernel Categories: kernel-modules Repositories: base OpenWrt release: OpenWrt-21.02.0 File size: 12kB ...

Your installation is outdated. You must install required kmods within 24 hours after flashing a snapshot.

Nov 05, 2021 · VLAN VLAN is the acronym for Virtual Local Area Network, it is a virtual partitioning of physical network switches on OSI layer 2. It is a way to keep network clients separated from each other even if they use the same shared physical network, without setting up a whole subnet and a router.

Feb 14, 2021 · kmod-macvlan Version: see kernel for details Description: A kernel module which allows one to create virtual interfaces that\\ map packets to or from specific MAC addresses to a particular interface\\ \\ Installed size: 8kB Dependencies: kernel Categories: kernel-modules Repositories: base OpenWrt release: OpenWrt-18.06.0 File size: 9kB License ...

mwan3 (Load balancing/failover with multiple WAN interfaces) * 21:02: Latest release: 2.10.13-1 * 19.07: Latest release: 2.8.16-1 * 18.06 or older: Not supported or maintained. About mwan3 The mwan3 package provides the following functionality and capabilities:

hello, i created the macvlan Ethernet ports as follows: ip link add link eth0 name veth0 type macvlan ifconfig veth0 up ip link add link ...

Name · kmod-macvlan ; Version · see kernel for details ; Description · A kernel module which allows one to create virtual interfaces that\\ map ...

09.01.2022 · kmod-macvlan Version: see kernel for details Description: A kernel module which allows one to create virtual interfaces that\\ map packets to or from specific MAC addresses to a particular interface\\ \\ Installed size: 11kB Dependencies: kernel Categories: kernel-modules Repositories: base OpenWrt release: OpenWrt-21.02.0 File size: 12kB ...

05.11.2021 · OpenWrt default configuration on such devices does usually mirror the stock configuration. Most of such routers only contain a single network interface (eth0), leading to a 5-port VLAN-enabled switch that is virtually partitioned into a …

Jul 23, 2021 · In this way a packet of a certain connection coming from the wan address of the router2 will do the following travel. to wan_address_router2:3389 --> router2 --> redirect to 172.16.1.1:3389 --> router1 --> mark connection as "router2" and redirect to 192.168.1.50:3389 ; response from 192.168.1.50:3389 to router1 --> router1 --> recognize the ...

Jan 06, 2017 · 为什么lede的luci里没有luci-app-macvlan或luci-app-syncdial，这样好用插件没有太可惜了啊~ Pääosa käyttäjistä ei kuitenkaan ymmärrä suomea ...

31.12.2021 · I don’t need to create a route in OpenWRT, as it will sit in my current LAN firewall zone ⤵️: config route option interface 'macvlan' option target '192.168.30.3' option netmask '255.255.255.255' I don’t need to create 10-fixroutes.sh inside the container, because it's not using the Docker bridge network 'on top' of the existing VLAN ...

Sep 18, 2021 · Docker macvlan network on OpenWRT x86. Hi, I’m trying to use OpenWRT x86/64 as a Docker host to run pihole attached to the LAN network of OpenWRT. I have done this before with an Ubuntu host where pihole is a docker container, running on the Ubuntu host connected to bridged Ethernet network. I had to do the macvlan workaround so that the ...

Hi, I'm trying to use OpenWRT x86/64 as a Docker host to run pihole attached to the LAN network of OpenWRT. I have done this before with an ...

I'm trying to use OpenWRT as a Docker host to run pihole attached the LAN network of OpenWRT. I have done this before with an Ubuntu host ...

Hi, i tried to use macvlan to have multiple interfaces on my lan ports. ... root@OpenWrt:~# cat /etc/config/network

Hi here, I need to add a WAN interface having a static IP address and share it with the LAN. I need a total of 3 WAN ports. For 2 of them, ...

23.07.2021 · Using multiple wan with multiple routers Problem The concept is: we have two or more router and every router has one wan connection active providing one public ip address.. Every router is connected to the same internal network (for now on called

14.02.2021 · kmod-macvlan Version: see kernel for details Description: A kernel module which allows one to create virtual interfaces that\\ map packets to or from specific MAC addresses to a particular interface\\ \\ Installed size: 8kB Dependencies: kernel Categories: kernel-modules Repositories: base OpenWrt release: OpenWrt-18.06.0 File size: 9kB License ...

Use macvlan networks. Estimated reading time: 3 minutes. Some applications, especially legacy applications or applications which monitor network traffic, expect to be directly connected to the physical network.

With single wan port is possible create virtual eths with kmod-macvlan. https://openwrt.org/docs/guide-user/network/wan/multiwan/mwan3?s[]= ...