Du lette etter:

openwrt can't access web interface

Networking – Can’t access openwrt access point’s admin ...
https://itectec.com/superuser/networking-cant-access-openwrt-access...
I've turned my TP-Link Archer C5 into an access point with this guide, using openwrt. It works correctly, and I can now access the internet through the wlan of the access point. I've set a static ip for the AP (192.168.1.2), as it said in the tutorial, but after connecting to the AP I have internet but can't reach 192.168.1.2.
Can't access OpenWrt web gui LUCI - Installing and Using ...
https://forum.openwrt.org/t/cant-access-openwrt-web-gui-luci/27914
27.03.2021 · Can't access OpenWrt web gui LUCI. Installing and Using OpenWrt. ... (sort of) and i do notice that not every interface that is setup can be accessed through the GUI. I have setup VLAN 1 on the WAN port (eth0) to connect to the edge router (because i need all 4 LAN ports) with IP 192.168.1.150 again. This i can´t access through the ...
LEDE/OpenWRT — Adding a Web Interface | by CT WiFi | LEDE ...
medium.com › openwrt-iot › openwrt-adding-a-web
Jan 20, 2016 · LuCI Web Interface (OpenWRT wiki) To start off with, your device will need internet access. The first step is to SSH into your device so you can run a few commands (We detailed the SSH steps in a ...
how to do initial login (ssh) if 192.168.1.1 can't be routed
https://itectec.com › superuser › op...
Now all the configuration I have done is written to the failsafe partition (I think). Is there a way to force Windows to allow me to ssh over the ethernet cable ...
Access point can't access web interface. : r/openwrt - Reddit
https://www.reddit.com › comments
I've set up an access point like https://openwrt.org/docs/guide-user/network/wifi/bridgedap , and it works perfectly, but I can't access the ...
Can't access OpenWrt web gui LUCI - Installing and Using ...
forum.openwrt.org › t › cant-access-openwrt-web-gui
Dec 29, 2018 · About 3 weeks ago i setup a R7800 (Netgear) with OpenWRT as a wireless accesspoint. 3 wifi networks 1 for LAN 1 for IoT and 1 for guests with seperated vlans. This all worked great and then i left on a holiday. I came back an noticed there was no guests network anymore. So yesterday i tried to access the web gui on the IP 192.168.1.150 with no ...
Can't access web interface for initial setup - Support
https://discuss.freedombox.org › ca...
Im using an olinuxino a20 lime2 with image from freedombox.org Box boots ok and stop on tty1 login. I try to access the interface trough 10.42.0.1 and ...
[OpenWrt Wiki] Internet connectivity and troubleshooting
openwrt.org › docs › guide-quick-start
In the OpenWrt admin web interface, go to Network → Diagnostics and Click on “ping” button or, if using OpenWrt SSH command line, you can use the command ping openwrt.org This should return “0% packet loss” if everything is alright with your Internet connection
[OpenWrt Wiki] Web interface overview
https://openwrt.org/docs/guide-user/luci/webinterface.overview
02.08.2021 · Webmin is a web-based interface written in Perl for system administration for Unix and Linux (but it wasn't ported to OpenWrt yet). Using any modern web browser, you can setup user accounts, Apache, DNS, file sharing and much more.Webmin removes the need to manually edit Unix configuration files like /etc/passwd, and lets you manage a system from the console …
Why can't I access the OpenWRT Web UI in Access Point Only ...
stackoverflow.com › questions › 52965789
Nov 01, 2018 · config interface 'lan' option ifname 'eth1 switch0' option type 'bridge' option proto 'static' option ipaddr '10.0.1.3' # MAC reservation on main router option netmask '255.255.255.0' I could connect and get an IP from the main router, but I could not ping my new router, nor access it over SSH or access the Web UI.
[OpenWrt Wiki] Accessing LuCI web interface securely
openwrt.org › docs › guide-user
Nov 10, 2021 · If you are doing admin things via LuCI web interface, there is a risk that a user of your OpenWrt network is sniffing your traffic. You are at risk of giving away your LuCI web credentials to attacker. There are some ways to mitigate this risk. Note that you need to choose wisely which of these methods suit your security needs.
can't access to web interface after upgrade : openwrt
https://www.reddit.com/r/openwrt/comments/ffhvpf/cant_access_to_web...
and I was able to connect via telnet following the instructions given in the section "Installation without opening the case (Web Interface Hack)". Before I copied the firmware, a power shutdown occurred and now I can't connect via telnet nor access to the web interface anymore. I tried by resetting the router several times but no success.
[OpenWrt Wiki] Web interface overview
openwrt.org › docs › guide-user
Aug 02, 2021 · Webmin is a web-based interface written in Perl for system administration for Unix and Linux (but it wasn't ported to OpenWrt yet). Using any modern web browser, you can setup user accounts, Apache, DNS, file sharing and much more. Webmin removes the need to manually edit Unix configuration files like /etc/passwd, and lets you manage a system ...
Why can't I access the OpenWRT Web UI in Access Point Only ...
https://stackoverflow.com › why-c...
Well, turned out to be the stupidest thing. While this line in my lan configuration appears flawed: option ifname 'eth1 switch0'.
Why can't I access the OpenWRT Web UI in Access Point Only ...
https://stackoverflow.com/questions/52965789
01.11.2018 · config interface 'lan' option ifname 'eth1 switch0' option type 'bridge' option proto 'static' option ipaddr '10.0.1.3' # MAC reservation on main router option netmask '255.255.255.0' I could connect and get an IP from the main router, but I could not ping my new router, nor access it over SSH or access the Web UI.
Can't access openwrt access point's admin interface - Super ...
https://superuser.com › questions
So apparently the problem was that my main router uses 192.168.178.* as the space to assign ip addresses in (which isn't standard, ...
OpenWrt can't acces host in Lan - Unix & Linux Stack Exchange
https://unix.stackexchange.com › o...
According to the guide you linked, you set up your OpenWrt router with masquerade. In other words, for every connection the RaspPi initiates ...
Can't access web GUI via 192.168.1.1 - OpenWrt Forum
https://forum.openwrt.org › cant-a...
I just flashes OperWrt to a Linksys EA4200v2 router, but I can't access the web GUI at 192.168.1.1. I flashed the router w/ firmware version ...
[OpenWrt Wiki] Accessing LuCI web interface securely
https://openwrt.org/docs/guide-user/luci/luci.secure
10.11.2021 · Accessing LuCI web interface securely If you are doing admin things via LuCI web interface, there is a risk that a user of your OpenWrt network is sniffing your traffic. You are at risk of giving away your LuCI web credentials to attacker. There are some ways to mitigate this risk.