srch

27.11.2021 · OpenWrt features a versatile RA & DHCPv6 server and relay. Per default SLAAC and both stateless and stateful DHCPv6 are enabled on an interface. If there are any prefixes of size /64 or shorter present then addresses will be handed out from each prefix.

27.11.2021 · How to use OpenWrt behind a Freebox with IPv6 delegation. IPv6 configuration. IPv6 extras. IPv6 multicast. IPv6 on L2TP softwire. IPv6 with Hurricane Electric. IPv6 with Hurricane Electric using LuCI. NAT6 and IPv6 masquerading. WIDE-DHCPv6 client configuration.

I just use the wizard enable DHCPv6 with Prefix Delegation /60 and I would get IPv6 and just works..but with OPENWRT I can get IPv6..but ...

Aug 09, 2020 · 楼主之前发过一篇【终极指南】关于N1做旁路由添加 iptables 自定义防火墙规则的见解 ，反应较好，解决了大家的疑惑。今天给大家带来一篇 N1 做旁路由，IPv6 的设置教程， ...恩山无线论坛

List all projects. Project Description Owner Last Change; buildbot.git: LEDE buildbot configuration

Installing and Using OpenWrt Network and Wireless Configuration ... However, because I am already using server mode for DHCPv6/RA because of ...

How to use OpenWrt behind a Freebox Crystal with IPv6 bridge ... NAT6 and IPv6 masquerading · WIDE-DHCPv6 client configuration.

01.12.2019 · PPPOE for the IPv4 wan, SLAAC on IPv6 wan, and DHCPv6 for prefix delegation. SLAAC works fine, wan6 or wan_6 interface (option ipv6 in pppoe-wan 1 or auto, tried them both) has a correct IPv6 and can see it works with pings etc. The problem seems to be with DHCPv6. With tcpdump I can see solicit from OpenWrt and advertise from server.

65 rader · 16.12.2021 · Possible section types of the dhcp configuration file are defined below. …

My ISP basically told me the same. His testing router (tp-link, not OpenWrt) successfully concluded the DHCPv6 sequence, while mine is stuck in ...

21 rader · WIDE-DHCPv6 client configuration The /etc/config/dhcp6c file controls the WIDE …

I'm trying to set up ipv6 address of my raspi running openwrt using dhpcv6. The address should be obtained from another router (running ...

10.09.2019 · I'm trying to set up ipv6 address of my raspi running openwrt using dhpcv6. The address should be obtained from another router (running openwrt too). That server has odhcp server running and my laptop has no problem obtaining ipv6. When I use odhcp6c on raspberry pi, I can see that server is responding (see request and response with tcpdump), but odhcp6c on …

21.11.2020 · OpenWrt 路由 IPv6 正确上网配置; Paragon ExtFS for Windows 下载+注册机; EditPlus v5.0.730 绿色汉化版及激活注册码@zd423; Cloudflare 全球平均速度12ms最快的 DNS！

The OpenWrt embedded DHCPv6-client odhcp6c is a minimal DHCPv6 and RA-client for use in embedded Linux systems. So I think it should handle RAs ...

Hi. I have been using openwrt for years and recently upgraded from 18.06 to 19.07 and realized that DHCPv6 seems not working properly.

28.06.2020 · wan口的拨号有好几种方式，SLAAC, stateless DHCPv6, stateful DHCPv6, DHCPv6-PD，这些请求方式在odhcpv6里面都可以配置。 1. odhcp6c客户端启动过程 开 …

DHCPv6-PD should work by default on OpenWrt. I have connected my travel router to my mother-in-law's Spectrum service, and I see that she has been allocated a /56, the OpenWrt router just grabbed a /64 out of the /56. You may want to back up your config, then default the OpenWrt router, and see if that works as you expect.

odhcpd is an embedded DHCP /DHCPv6/RA server & NDP relay. Abstract. odhcpd is a daemon for serving and relaying IP management protocols to ...

The /etc/config/dhcp6c file controls the WIDE-DHCPv6 client package wide-dhcpv6-client configuration. It defines basic properties and interface ...

When the modem is switched to bridge mode, OpenWrt receives an IPv6 address via DHCPv6, but no prefix delegation is configured for the wan6 ...

27.11.2021 · NAT6 and IPv6 masquerading This article relies on the following: * Accessing OpenWrt CLI * Managing configurations * Managing packages * Managing services Introduction This page describes how to set up NAT6 aka NAT66 with IPv6 masquerading on your OpenWrt router. Most users will not need or want to do this in IPv6, but there are some more specific …

Dec 24, 2021 · 开始时在 openwrt 里是能 Ping 通外网的，局域网 PC 能获取到 ip ，能 ping 通路由，但无法 ping 外网 ip 。最后发现是在 openwrt DHCPV6 服务里要钩上“Always announce default router”，这样局域网内的设备就连上外网了，现在也能通过你这个网站的测试。