srch

27.11.2021 · How to use OpenWrt behind a Freebox with IPv6 delegation. IPv6 configuration. IPv6 extras. IPv6 multicast. IPv6 on L2TP softwire. IPv6 with Hurricane Electric. IPv6 with Hurricane Electric using LuCI. NAT6 and IPv6 masquerading. WIDE-DHCPv6 client configuration.

So, my OpenWRT router is behind another router. ... config dhcp 'wan6' option dhcpv6 relay option ra relay option ndp relay option master 1.

11.05.2021 · OpenWRT IPv6 中继模式. IPv6 relay 模式怎么配置网上有一大把教程，就不多说了。. 重点在于为什么客户端能获取地址却 ping 不通公网，但 ping 一下路由器的 wan IPv6 地址后就可以上网了。. 通过在客户端设备上抓包和查看 ip neigh （或 ndp -an ）可以发现，区别在于 IPv6 ...

odhcpd is an embedded DHCP /DHCPv6/RA server & NDP relay. Abstract. odhcpd is a daemon for serving and relaying IP management protocols to ...

So I managed to get IPv6 addresses for my OpenWRT device: ... cat /etc/config/dhcp config dhcp wan option dhcpv6 relay option ra relay ...

19.03.2015 · config dhcp 'wan' option interface 'wan' option ignore '1' config dhcp 'wan6' option interface 'wan6' option ra 'relay' option dhcpv6 'relay' option ndp 'relay' 6relayd配置 这里其实有两个选择，odhcpd或者6relayd，OpenWrt官方推荐的是odhcpd，不过在我的配置过程中用odhcpd经常拿不到IPv6地址，最后还是选择了6relayd。

42 rader · 01.10.2021 · odhcpd is an embedded DHCP /DHCPv6/RA server & NDP relay. Abstract …

03.11.2021 · Wi-Fi extender / repeater / bridge configuration If supported by both devices, consider using WDS, Layer 2 GRE tunnels (“gretap”), or mesh networking. Using relayd as instructed in this article isn't guaranteed to work. The most common problem is that the client router cannot pass the

I found that M=O=0 in this pcap, which means that our university uses SLAAC to assign ipv6 address. So I disable dhcpv6 in the second pcap. The MAC address of ...

65 rader · 16.12.2021 · Possible section types of the dhcp configuration file are defined below. …

15.09.2020 · mostly, while configuring the dhcp, the dhcp server may not be connected to clients directly in practical scenarios due to management reasons.in such cases, a dhcp relay agent serves the purpose relaying the messages coming from the clients and server.the dhcpv6 relay agent uses relay forward/reply messages to relay the messages between servers …

Installing and Using OpenWrt Network and Wireless Configuration ... However, because I am already using server mode for DHCPv6/RA because of ...

Hey all, New to IPv6 on OpenWRT on 19.07.5 with a TP-Link AC1750. ... ra 'relay' option ndp 'relay' config dhcp wan6 option dhcpv6 'relay' ...

27.03.2017 · Dear community, I have just switched my WZR-HP-G300H box from OpenWrt to LEDE 17.01.0-rc1. While there is no problem about IPv4, IPv6 is not working on clients. I'm using relay mode without upstream dhcpv6 and the rout…

How to use OpenWrt behind a Freebox Crystal with IPv6 bridge ... NAT6 and IPv6 masquerading · WIDE-DHCPv6 client configuration.

01.03.2015 · The relay mode does not work on my OpenWRT router. Devices on LAN can get inet6 addr but are unable to ping any public ipv6 address. By Googling odhcpcd and ipv6 relay, I find many similar problems but no one of them are solved. Therefor...

So this is my /etc/config/network: config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option ...

Hello, I have few questions about dhcpv6 in openwrt. I understood that relay mode is used only if the ISP gives just a /64 without prefix ...

27.11.2021 · OpenWrt features a versatile RA & DHCPv6 server and relay. Per default SLAAC and both stateless and stateful DHCPv6 are enabled on an interface. If there are any prefixes of size /64 or shorter present then addresses will be handed out from each prefix.

... IPv6 relay mode seems to work However LUCI is not consistent with this use case Normally in this network setup you add a WAN6 as DHCPv6 ...