srch

Jan 17, 2019 · hello, i finally got igmpproxy installed and my router settings are set to default. What settings need to be changed to allow multicast from WAN to LAN ? I read many posts on this topic but I can't get it to work. Please help. PC1(10.0.0.50) sends multicast stream (239.1.1.1:1234) to a switch and PC2 is connected over LAN to my router (192.168.1.1). Then I connected the WAN to the switch ...

This software is available in the official source of OpenWRT, but it can be installed directly, but the configuration is more payive. Profile in / etc / config / igmpproxy config igmpproxy Option Quickleave 1 // Enable Quickleave config phyint Option network eth0.1 // uplink port, that is, the route is to connect to Modem, the specific number varies from person to person.

Jan 18, 2019 · The igmpproxy adds routes and rules to the kernel which cause the kernel to forward these multicast UDP packets received on the WAN to the LAN where they are received by the original requester. First you need to install the package opkg install igmpproxy You need to edit /etc/config/igmpproxy according to your setup.

Introduction

Download igmpproxy_0.2.1-4_x86_64.ipk for OpenWrt 19.07 from OpenWrt Base repository.

Openwrt与IPTV之一----igmpproxy. IPTV之igmpproxy配置. 装了IPTV，设备是一个cable modem和一个IPTV STB. 前者把HFC变成普通的以太网，后者负责解码和播放。. 本着有RJ45的设备，都插电脑抓抓包的习惯，发现直播是基于组播的，协议用的是RTP。. 全能播放器VLC出马，输入对应 ...

First you need to install the package opkg install igmpproxy. I presume that the "opkg" command is part of the default OpenWrt installation ...

Let me talk about igmpproxy first, as the name implies, realize the proxy of igmpproxy protocol~ This software is available in the official source of openwrt, you can install it directly, but the configuration is more particular.

18.01.2019 · Adding a line such as this to the /etc/firewall.user may be required: iptables -t mangle -A PREROUTING -i eth0 -d 224.0.0.0/4 -p udp -j TTL --ttl-set 2. This will cause multicast UDP packets to have a TTL of 2 prior to being routed by OpenWrt allowing them to be sent out the LAN interface with TTL =1. You can increase the value further if you ...

Dec 19, 2021 · Self-registration in the wiki has been disabled. If you want to contribute to the OpenWrt wiki, please post HERE in the forum or ask on IRC for access.

17.09.2021 · #Client Bridged / Client Mode / RelayD and IGMPProxy (It works) # RelayD is to redirect packages and IGMP is for redirect IGMP packages # Our network is 192.168.1.0/24 # Steps: # Configure WAN as static # We should edit our wan iface and put static IP uci set network.wan= ' interface ': uci set network.wan.proto= ' static ': uci set network.wan.ipaddr= ' …

01.11.2021 · ISP Configurations This page describes how to connect to networks of different commercial Internet service providers. At this time, most of the DSL configurations described below only apply to modem-router devices using Lantiq SoC. There is no DSL support for Broadcom devices. This article may contain network configuration that is version dependent …

03.02.2013 · I am using a Openwrt router acting as WIFI client to allow computers to connect to this Openwrt router via ethernet. A few lessons I learned these few days trying to setup my network here using relayd 1) ... Btw, do you know howto install luci-app-igmpproxy? opkg install luci-app-igmpproxy doesn't work..

Install Howto. Fetch a list of available packages: # opkg update; Install igmpproxy ipk package: # opkg install igmpproxy ...

How to setup Client Bridged / Client Mode / RelayD and IGMPProxy for OpenWRT / LEDE - relayd-igmpproxy.sh.

package: igmpproxy. ... Name: igmpproxy; Version: 0.2.1-4; Description: IGMPproxy is a simple ... Installed size: 18kB; Dependencies: libc ...

Is there an opkg I need to install or something? ... tried scmroute after banging my head up against igmpproxy for two days straight.

The transmission range depends on many factors. The true distance is based on the antenna installing height , antenna gain, using environment like building and other obstructions , sensitivity of the receiver, antenna of the receiver .

I know it is bit late, but i guess it will help someone who is still looking for answer. Install IGMPProxy install igmpproxy make menuconfig ...

Ctrl+T,输入ifconfig查看. option bind 'br-lan'是填路由器的内网地址，填'br-lan'比具体的IP如192.168.2.1要好，内网地址变也不用修改了. option source 'eth0.4'是填组播的地址，我拿高恪K2P来说,外网配置-->弹性接口,设置WAN1,WAN2其余作为LAN口，然后”接口概览“显示得 …

19.12.2021 · igmpproxy Version: 0.2.1-4 Description: IGMPproxy is a simple dynamic Multicast Routing Daemon using\\ only IGMP signalling (Internet Group Management Protocol).\\ \\ Installed size: 15kB Dependencies: libc, librt, libpthread Categories: network---routing-and-redirection Repositories: base Architectures:

07.06.2018 · If you're not sure what to specify for altnet, comment it out and look for the igmpproxy output in the log (or on stdout if you start it in debug mode - you can simply test by igmpproxy -d /etc/igmpproxy.conf), it'll say something like Warn: The source address 10.254.16.66 for group 233.32.240.222, is not in any valid net for upstream VIF. and so you'll …

I connected via SSH, I try to install the igmpproxy package from the repository, I get the following ... root @ Gargoyle: ~ # opkg update