srch

24.07.2015 · My new provider IPv6 connectivity, however after connecting my OpenWrt based WNDR4300 (using Chaos Calmer 15.05-rc3) things unfortunately did not “just work”… This post summarize some hints how to debug IPv6 on OpenWrt. First, make sure that the upstream (WAN) interface is configured according to the documentation in the OpenWrt Wiki.

Nov 27, 2021 · IPv6 configuration See also: Routing example: IPv6, IPv4/IPv6 transitioning The default firmware provides full IPv6 support with a DHCPv6 client (odhcp6c), an RA & DHCPv6 Server (odhcpd) and a IPv6 firewall (ip6tables). Also, the default installation of the web interface includes the package luci-proto-ipv6

Hi, firstly sorry for my bad english... I have a TP-Link Archer C60 V2.0, Running latest 18.06.4, connected via bridge to a Fiberhome ...

Upgrade back to the 18.x firmware. That's all, magically the IPv6 WAN Upstream is finally connecting. For #2, i.e. LAN configuration, set it up as follows: Network - Interfaces - LAN - Common Configuration - General Setup tab - IPv6 assignment length must be set to the length of your prefix.

Jul 24, 2015 · My new provider IPv6 connectivity, however after connecting my OpenWrt based WNDR4300 (using Chaos Calmer 15.05-rc3) things unfortunately did not “just work”… This post summarize some hints how to debug IPv6 on OpenWrt. First, make sure that the upstream (WAN) interface is configured according to the documentation in the OpenWrt Wiki.

Apparently OpenWRT's IPv6 client odhcp6c expects regular RA sollicitations from upstream router. Without RA messages the default route times ...

Hi everyone! I'm having issues connecting my router to the upstream Comcast ipv6 network. IPv4 upstream works just fine.

Documentation · User guide · Network · IPv6 · How to use OpenWrt behind a Freebox Crystal with IPv6 bridge · How to use OpenWrt behind a ...

Hi, I'm using a UBNT-ERX running OpenWrt 18.06.4. It is connected to a AVM Fritz!Box 7430 (Upstream) which is providing the access to VDSL ...

Nov 27, 2021 · How to use OpenWrt behind a Freebox with IPv6 delegation. IPv6 configuration. IPv6 extras. IPv6 multicast. IPv6 on L2TP softwire. IPv6 with Hurricane Electric. IPv6 with Hurricane Electric using LuCI. NAT6 and IPv6 masquerading. WIDE-DHCPv6 client configuration.

27.11.2021 · NAT6 and IPv6 masquerading This article relies on the following: * Accessing OpenWrt CLI * Managing configurations * Managing packages * Managing services Introduction This page describes how to set up NAT6 aka NAT66 with IPv6 masquerading on your OpenWrt router. Most users will not need or want to do this in IPv6, but there are some more specific …

Hi all! I am a newbie with ipv6, my ISP just started sharing it. Why i have no ipv6 Upstream? While ipv4 wan have ipv6 ip address.. there is ...

I can't seem to figure out if this is an ISP or known bug with OpenWRT but I occasionally lose the IPv6 upstream after a certain period of time. Usually the next morning, the router loses IPv6 address until I restart the interface manually. Settings. Request IPv6-address: force. Request IPv6-prefix of length: 56 (this is my ISP's spec for IPv6)

Dec 22, 2019 · Not if the upstream router doesn't support this (and doesn't even implement DHCPv6-PD properly), which is the problem at hand. Neither if there are devices connected to said upstream router, which are getting their connectivity (including IPv6) from said upstream router, in parallel to the OpenWrt router's WAN.

Interesting issue showed up today... For reference, this is not my gateway device... This is a router I have sitting on the LAN only to ...

27.11.2021 · How to use OpenWrt behind a Freebox with IPv6 delegation. IPv6 configuration. IPv6 extras. IPv6 multicast. IPv6 on L2TP softwire. IPv6 with Hurricane Electric. IPv6 with Hurricane Electric using LuCI. NAT6 and IPv6 masquerading. WIDE-DHCPv6 client configuration.

ISP --> ISP modem/router (technicolor) (not bridged) --> WNDR3700 router (OpenWrt 18.06.5) --> LAN, wifi & wifi guest. TV, XBOX and Hometheatre ...

I have no IPv6 WAN upstream as my ISP only gives IPv4. ... I also see that on the OpenWrt Router there are IPv6 routes.

I can't seem to figure out if this is an ISP or known bug with OpenWRT but I occasionally lose the IPv6 upstream after a certain period of time. Usually the next morning, the router loses IPv6 address until I restart the interface manually. Settings. Request IPv6-address: force. Request IPv6-prefix of length: 56 (this is my ISP's spec for IPv6)

16.12.2021 · OpenWRT interface name (NOT network device name) where the destination DHCP server is located. local_addr: string : yes (none) This OpenWRT device's own IP address on the far subnet, where it will listen for DHCP requests. server_addr: string : yes (none) IP address of the upstream DHCP server accessible through the network given by the ...

Flow_offloading=1 is broken on latest snapshot (4.19 issue) · Does R7800 work with ipv6? · OpenWrt looses IPv6 connectivity after upstream outage/ ...

27.11.2021 · IPv6 configuration See also: Routing example: IPv6, IPv4/IPv6 transitioning The default firmware provides full IPv6 support with a DHCPv6 client (odhcp6c), an RA & DHCPv6 Server (odhcpd) and a IPv6 firewall (ip6tables). Also, the default installation of the web interface includes the package luci-proto-ipv6