srch

22.08.2020 · Hi, I'm not new to networking but pretty new to OpenWrt, that's basically why I'm here. Having said that, let's get to the problem: I'd like to configure my TL-WR841N with OpenWrt installed (obviously) as a "managed switch" and set it to use the WAN port as trunk to/from the main router (which is a Pfsense custom build). Here I have the diagram of the network I'd like …

Jan 03, 2020 · Then, in the Netgear Switch, I created a VLAN with VLAN ID of 1, and another with a VLAN ID of 3, just like in the OpenWRT Router. The cable coming from the OpenWRT Router, connected to the Switch, was connected to Port 1, so, I tagged this port in both VLANS, and untagged the ports that I wanted to use for each VLAN. Here are some screenshots:

Jul 23, 2021 · So the idea is to reserve some ports in a managed switch with VLANs to configure them as extension for a OpenWrt based gateway. A point that should not be underestimated is how to choose and reserve ports for specific roles. For now we can decide to divide the role of the ports in two main groups: external connection and internal connections ...

Version 21.02.0 of the OpenWrt router distribution is out. ... The following targets are using a switch managed with DSA in OpenWrt 21.02: ...

23.07.2021 · So the idea is to reserve some ports in a managed switch with VLANs to configure them as extension for a OpenWrt based gateway. A point that should not be underestimated is how to choose and reserve ports for specific roles. For now we can decide to divide the role of the ports in two main groups: external connection and internal connections.

04.04.2019 · VLAN tagging on OpenWRT/managed switches. By Atomstar on Wednesday 3 April 2019 20:31 - Comments (5) Category: Smarthome, Views: 6.406 I wanted to place my router somewhere not in the meterkast, so I used VLAN tagging on a managed switch to get the WAN data to the router and my LAN data back on the same wire (but different VLAN) ...

Nov 05, 2021 · Newer devices with embedded switches (like Netgear R7800) use the DSA switch driver, that creates a distinct network interface for each switch port as if they didn't have a switch at all. Most OpenWrt-supported devices can use the DSA driver, but they aren't ported over yet because the switch configuration would change significantly and likely ...

Apr 04, 2019 · Netgear GS108E v3 managed switch; Archer C7 v2 with OpenWRT; Configuration on router and switch On my switch, I receive WAN traffic (VLAN34) on port1, and use port2 to both forward the WAN traffic to my NAT'ing router, as well as receiving the LAN traffic back from the router: VLAN config: which ports are part of which VLAN:

Instead of using a NETGEAR 5-Port Gigabit Smart Managed Plus Switch for this, you could use an OpenWRT flashed WRT54G router, by configuring its switch.

You have a powerful machine running OpenWrt. Powerful here means: a device able to process the amount of network packets ...

13.04.2020 · Please visit my channel https://www.youtube.com/channel/UCG5Ph9Mm6UEQLJJ-kGIC2AQWe are using OpenWRT to build a managed switch with VLAN functionality from a...

I've also been looking for a higher port switch to manage with OpenWRT (or really anything open and text based). In the meantime, the Archer C7's which are really popular here have a 5 port switch (actually more, because the CPU has ports on the switch too).

Please visit my channel https://www.youtube.com/channel/UCG5Ph9Mm6UEQLJJ-kGIC2AQWe are using OpenWRT to build a managed switch with VLAN functionality from a...

VLAN tagging on OpenWRT/managed switches ... so I used VLAN tagging on a managed switch to get the WAN data to the router and my LAN data ...

Instead of purchasing an expensive manageable switch that supports VLANs, I ended up flashing OpenWRT on a couple Linksys E4200v2 wireless ...

Is there a managed switch with an ASIC on which OpenWRT can run? I'd like the openness of OpenWRT and the performance of hardware ...