srch

Mar 02, 2021 · Interesting, thanks for sharing that information. Since switching the dnsmasq to handle IPv6 with the enable-ra, I don't seem to be having the same issues I've had with IPv6 leases being lost on clients after a while, so I may just keep dnsmasq for IPv6 and have odhcpd disabled.

Oct 19, 2016 · 21 Oct 2016, 01:57. What I mean is that in my use case (and many share this) OpenWRT must act as a DHCPv6-PD client to the ISP (using odhcp6c by default), getting a prefix, and then act as a server to the LAN with the delegated prefix (using odhcpd by default). The discussion might have continued from here.

Dec 28, 2021 · DNS and DHCP examples See also: DNS and DHCP configuration, DNS encryption, DNS hijacking Introduction This how-to provides most common dnsmasq and odhcpd tuning scenarios adapted for OpenWrt. Instructions Static leases LuCI -> DHCP and DNS -> Static Leases Add a fixed IPv4 address 192.168.1.22 and name

For larger networks, ODHCPD targets real prefix delegations, lets say IPV6::/48 properly delegated to different buildings and floors with various firewall/security rules between departments. OpenWRT users are significantly represented by residential and small-business users of one master router and maybe a few repeaters.

58 rader · 03.11.2019 · OpenWrt uses dnsmasq and odhcpd to serve DHCP and DNS by default. …

42 rader · 01.10.2021 · odhcpd is a daemon for serving and relaying IP management protocols …

The examples provided here are serial dnsmasq with unbound, parallel dnsmasq with unbound, and unbound scripted with odhcpd. Serial dnsmasq. In this case, dnsmasq is not changed much with respect to the default OpenWrt configuration. Here dnsmasq is forced to use the local Unbound instance as the lone upstream DNS server, instead of your ISP.

16.08.2020 · OpenWrt has odhcpd as well I think, which by default only handles IPv6 but should be able to do IPv4 as well. But dnsmasq should work just fine. You're better off looking at the config files themselves - e.g. /etc/config/dhcp.

19.10.2016 · 21 Oct 2016, 01:57. What I mean is that in my use case (and many share this) OpenWRT must act as a DHCPv6-PD client to the ISP (using odhcp6c by default), getting a prefix, and then act as a server to the LAN with the delegated prefix (using odhcpd by default). The discussion might have continued from here.

The following will configure dnsmasq to provide DHCP (assigning .1–.100), and DNS (e.g., assigning the hostname server.example.com to the computer with MAC ...

Odhcpd seems a better option than dnsmasq, it's an DHCP, DHCPv6 and RA server designed and implemented by OpenWRT with a very good ...

27.06.2019 · Hi! I'm trying to replace dnsmasq with unbound and odhcpd. I followed the steps from here: It works for the most part but some things aren't working. Static DHCP Leases, static ip is given out correctly but the configured hostname is not used DHCP leases disappear from luci status overview page local domain resolution only works on the router and not on the clients …

By setting up DNSSEC on your OpenWrt router, you protect your entire ... support) and remove odhcpd-ipv6only: opkg install dnsmasq-full ...

My home router runs OpenWRT, which uses dnsmasq by default. ... This isn't a feature of dnsmasq, so I need to install dhcpd and bind instead ...

Oct 01, 2021 · odhcpd See also: odhcpd upstream documentation odhcpd is an embedded DHCP/DHCPv6/RA server & NDP relay. Abstract odhcpd is a daemon for serving and relaying IP management protocols to configure clients and downstream routers. It tries to follow the RFC 6204 requirements for IPv6 home routers.

odhcpd is usually only used for the IPv6 side of things (yes, there is a full -non-default- version that could also replace dnsmasq ...

I've seen various guides and tutorials online, some suggest installing Unbound and removing dnsmasq and replacing it with odhcpd, ...

Привет! 29 Oct 17 21:30, you wrote to me: VS> Не вижу в этом логе ни слова ... Сообщения DHCP есть только общие: daemon.info odhcpd[792]: ...

28.12.2021 · DNS and DHCP examples See also: DNS and DHCP configuration, DNS encryption, DNS hijacking Introduction This how-to provides most common dnsmasq and odhcpd tuning scenarios adapted for OpenWrt. Instructions Static leases LuCI -> DHCP and DNS -> Static Leases Add a fixed IPv4 address 192.168.1.22 and name

65 rader · 16.12.2021 · dnsmasq. /etc/config/dhcp. DHCP. 67/ UDP, 68/ UDP. DHCPv6. 547/ UDP. odhcpd-ipv6only. Dnsmasq serves as a downstream caching DNS server advertising itself to DHCP clients. This allows better performance and management of …

25.01.2018 · Odhcpd seems a better option than dnsmasq, it's an DHCP, DHCPv6 and RA server designed and implemented by OpenWRT with a very good integration. Furthermore dnsmasq is the originator of many issues, so ideally Libremesh will get rid of dnsmasq In the future. Currently dnsmasq is used as DHCP server but also as DNS server.

Dec 16, 2021 · See the dnsmasq man page for details on the syntax of the O option. The configuration options in this section are used to construct a -M option for dnsmasq. *Note*: odhcp currently lacks support root-path specification. If you need this functionality, disable odhcpd and use dnsmasq instead.