srch

I am using static ip. Should i enter the router ip in the preferred dns settings of each AP?

I have a new Unifi setup (5.10.26) and I'm learning on the fly. I noticed that there are several levels of configuring DNS. I originally set it up at the USG level: 1.1.1.1 / 8.8.8.8

18.04.2021 · UniFi Firewall Basics: DNS for a Guest Network Firewall Rule Interface and Direction. Now that I covered VLAN and subnet basics, I want to get a little more practical.Once you have your VLANs and subnets setup, the next big thing to look at is firewall rules.

Nov 23, 2021 · UniFi’s Advanced Wi-Fi settings are often misunderstood. The defaults are usually safe, but it’s helpful to understand what these settings do while setting up a network or troubleshooting an issue. Ubiquiti doesn’t do the best job at explaining, so lets go through them one by one. These settings and descriptions are using the default ...

Log in to Ubiquiti UniFi controller. · Go to the Settings tab. · Navigate to Networks. · Click Edit Network > WAN. · Proceed to Common Settings > DNS Server and ...

Chapter 3: Using the UniFi Controller Software . ... Chapter 12: UniFi Access Point Details . ... Preferred DNS Enter the IP address of the service.

All right, so the UniFi Controller is ready to go. ... The Preferred DNS, enter the router's IP address as well, so it uses the Cloudflare ...

Anyway, I noticed it had its own preferred DNS settings. I do not recall ever seeing that and am suspecting it was part of why I was not seeing some device traffic on my PiHole (recent add, with a static IP). What is the intended behavior of this? I configured the AP with a static IP and set preferred DNS to my Pi Hole.. Any issues with that?

I have a new Unifi setup (5.10.26) and I'm learning on the fly. I noticed that there are several levels of configuring DNS. I originally set it up …

For TM subscribers other than unifi and Streamyx. - Please set your DNS to: Primary: 202.188.18.188 Secondary: 1.9.1.9. ▫ Laptop/Desktop.

Solution: You need to go into the Unifi Controller, Settings, Networks, edit your LAN settings, click the box to "Enable DHCP Server" and configure your.

The Preferred DNS, enter the router’s IP address as well, so it uses the Cloudflare DNS that we set up earlier. For the Alternate DNS, we can enter the Google DNS as a backup. Lastly, click on Queue Changes and then Apply Changes. You can then do the same thing to the access point. Keeping the same subnet mask, gateway, and DNS settings.

06.01.2019 · In this article we will look at how to apply DNS redirection on your Unifi network. Please note this is for IPv4 DNS requests. To catch and redirect IPv6 DNS requests, please check the corresponding article. The goal is to catch and intercept DNS traffic that is NOT going through my carefully crafted infrastructure and…

23.01.2020 · Follow these steps to set the DNS server for a network. 1. Navigate to the Settings Gear > Networks> Network Name > DHCP Name Server 2. Toggle the radio button to Manual and enter the desired DNS server address(es). 3. Hit Save. Your clients will not get this change immediately, I had to release/renew the DHCP lease to recieve the updated DNS server settings.

You set the DNS server in the controller by going to Settings>Network and clicking edit on the network that you want to set the DNS server for.

Oct 14, 2019 · The Preferred DNS, enter the router’s IP address as well, so it uses the Cloudflare DNS that we set up earlier. For the Alternate DNS, we can enter the Google DNS as a backup. Lastly, click on Queue Changes and then Apply Changes. You can then do the same thing to the access point. Keeping the same subnet mask, gateway, and DNS settings.

Posted: (1 week ago) I think the WAN > Preferred/Alternate DNS can be set for all UniFi devices so they can bypass the DNS servers listed in the Networks > DHCP Name Server. I left it blank on a switch and put a bad address in an AP as a test.

Jan 06, 2019 · First, create a new firewall group containing the list of allowed DNS entries. Do this via the unifi-interface. Use the “Routing & Firewall” – “Firewall” – “Groups” menu options for this: Adding firewall address group. My group has 10 entries: 4x USG IP addresses, 1 per VLAN. Then, the two Samba AD servers, the one Pi-Hole ...

Preferred DNS Enter a primary DNS address. - Alternate DNS Enter a secondary DNS address. Click apply to save any changes that you have made. Access Point ...