srch

You can use USG as timeserver. By default it synchronises against the NTP pool and your clients can sync against the USG. Unless you have the need for ...

Problems with USG as NTP server ignoring UDP source port 123. I · ifyffe · UniFiUniFi Routing & Switching.

03.01.2022 · I was also experiencing the same problem. Reboot the set top box (STB) but it asked for Unifi TV username and password - have entered the credentials but to no avail.

Furthermore, the controller settings in Services > NTP apply to all devices (including the USG itself). As a workaround one can set only the first NTP server to ...

I verified the NTP server in the USG's config and on my box it was configured to 0.ubnt.pool.ntp.org in the ntp.conf file. I then looked at the output using the ...

If it do that, can I direct my servers to use the usg3p as the ntp-server? As for now I need to port forward the udp 123 port and I don't want to do that, so ...

If I instead use "w32tm /stripchart /computer:0.ubnt.pool.ntp.org /dataonly /samples:5" w32tm uses Src Port: 60709 and Dst Port:123 and I get full server ...

Jul 17, 2016 · The following commands will set the NTP servers on EdgeOS-based Ubiquiti products. set system ntp server 0.pool.ntp.org set system ntp server 1.pool.ntp.org set system ntp server 2.pool.ntp.org set system ntp server 3.pool.ntp.org. Verify that your device's timezone is set correctly. Many organizations choose to set all their devices to UTC time.

This article describes how to configure DHCP options outside of the standard set on the UniFi Network web application. This applies to UDM and USG models with the latest firmware. Note: For more information on DHCP, see Intro to Networking - Dynamic Host Configuration Protocol (DHCP) .

11.10.2019 · SNMP allows external network software to monitor the status of your UniFi gear. NTP synchronizes the controller’s system time to a particular …

17.07.2016 · The following commands will set the NTP servers on EdgeOS-based Ubiquiti products. set system ntp server 0.pool.ntp.org set system ntp server 1.pool.ntp.org set system ntp server 2.pool.ntp.org set system ntp server 3.pool.ntp.org. Verify that your device's timezone is set correctly. Many organizations choose to set all their devices to UTC ...

Can the Secure Gateway Pro be the master for client machines for NTP? So the USG maintains it's time from a server on the internet, and then the clients ...

All you will need is two USG’s with both sites manage on the same site in Unifi Controller. You then just follow these steps: Open settings in Unifi Controller. Browse to Networks. Select ‘Create New Network’. On the purpose option, select Site-to-Site VPN. Watch the video below by Willie Howe for the full setup.

UniFi - USG/UDM: Configuring RADIUS Server This article describes how to configure the RADIUS server on the USG and UDM models. This server can be used for wired, wireless, and L2TP remote access authentication types.

I recently replaced my home gateway with a USG, and mostly like it so far. However, my former one was also my local NTP server.

If you had a USG it would provide NTP server services, as would any EdgeRouter. In fact many gateway devices from many vendors have similar functionality.

Oct 11, 2019 · For the most part with the exception of SNMP, NTP, and “Scheduled Upgrades”, you will need a USG for everything else. SNMP allows external network software to monitor the status of your UniFi gear. NTP synchronizes the controller’s system time to a particular server.

If you wan to use it for the Unifi Environment then you set the NTP Server IP Address in Settings->Services->NTP. As you are not using the USG, then DHCP ...

Dec 21, 2021 · NTP storm between KP125 and UniFi USG. 2021-12-21 14:19:25 - last edited 2021-12-21 18:17:02. Greetings, I'm seeing a massive amount of traffic (2000 packets per second, per device) between my KP125 smart plugs and my UniFi USG gateway's NTP daemon. My DHCP server provides the ntp-server option, the gateway is running ntpd "NTP daemon program ...

DHCP TFTP Server Option 66; DHCP WPAD URL Option 252; DHCP WINS Server Option 44; Additional custom options can be specified using the DHCP Option Code. This article describes how to configure DHCP options outside of the standard set on the UniFi Network web application. This applies to UDM and USG models with the latest firmware.

18.04.2021 · Hallöchen ihr lieben.Ich hab ein neues Problemchen wo ich nicht weis wie ich anfangen soll.Ich habe seit kurzem ja den USG-Pro 4Port im einsatz.Nun funktioniert mein Magenta TV Reciver 401 nicht mehr und Zeigt den Fehler: "NTP-Server antwortet nicht"…