srch

13.03.2015 · Brand Representative for Veeam Software Currently, we rely on a drive default block size. The described issue happens when there is a block size mismatch between the tape media and drive. Third party software changed the default block size of the media, while the drive default block size remained unchanged.

Backup to Tape Job to the HPE LTO tape drives fails with "Tape error: '1117'" after upgrade to Veeam Backup & Replication 9.5 Update 4b

12.05.2014 · WinApi Function 'Erase Tape' failed code 1117 message "The request could not be performed because of an I/O device error" There is no feedback to say a tape has been write protected. When you try and do an erase on it you get the above message. You can check in Device manager, when a tape is loaded you get a tab with information about the tape.

Tape positioning error: Tape error: '1117' (The request could not be performed because of an I/O device error.) TapeDrive alert: The tape drive ...

03.06.2015 · Thank you OP for posting your solution. I rolled back to 9.50 and all is hunky dory. Note: For those doing the roll back, if you cannot install the 9.50 WBEM agent then it's a problem with the Visual C++ 2012 RTM being installed from installing the HP Insight Management Agent.

13.05.2014 · For all versions of Veeam B&R: Additionally you may need to increase StorPort timeouts by creating a "StorPort" key with entries for all tape devices. You can get DEVICEID & INSTANCE with the following PowerShell command: gwmi -class win32_tapedrive. Location: KLM\System\CurrentControlSet\Enum\SCSI\ DEVICEID \ INSTANCE \Device …

31.07.2019 · This brings the tape drive into the faulty state. Solution To solve the issue, apply the hotfix: Download the hotfix. Check the current version of Veeam Backup & Replication. It must be 9.5.4.2866. Make sure that no jobs are running, close the console, and stop all Veeam services.

31.01.2006 · I relaunched the robocopy job that replicates the F: drive to the G: drive, and have NOT seen the same errors I was seeing before. It has completely replicated 547 GB of 50 KB files (which is an enourmous amount of files) without any errors. As it was before, it started throwing errors around 250 GB.

Jan 23, 2006 · No, none of the iSCSI targets are shared. I have 2 different ones in Starwind for 2 different servers. Same for the EMC targets. My log file is 1.2 Gig large, I can't even open it.

01.04.2013 · - Unable to read from disk - Error Code 1117 - The request could not be performed because of an I/O device error. Description Error code 1117 is generated by the Windows operating system and is always caused by I/O (Input / Output) throughput issues with either the disk or the controller that it is attached to. Check the disk for possible errors

During a tape related process in Veeam Backup & Replication the error “An attempt to access data before the beginning-of-medium marker ...

There is no feedback to say a tape has been write protected. When you try and do an erase on it you get the above message. You can check in ...

Hello, i'm using a HP Lto5 SCSI drive with veeam b&r community edition version 10. My file to tape job is failing with error 1117, ...

All Veeam servers without tape infrastructure components are ... Tape error: '1117' (The request could not be performed because of an I/O ...

19.07.2021 · Tape Devices Support. Veeam provides native tape support that is fully integrated into Veeam Backup & Replication. You can administer all operations on tapes from your Veeam console. Long-term archiving and compliance are listed as primary reasons for using tape. Tape appears to be one of the most widely used media for offsite backup.

2019 15:49:58] <01> Error Tape error: '1117' (The request could not be performed because of an I/O device error) (Veeam.Backup.Common.

May 06, 2014 · WinApi Function 'Erase Tape' failed code 1117 message "The request could not be performed because of an I/O device error" There is no feedback to say a tape has been write protected. When you try and do an erase on it you get the above message. You can check in Device manager, when a tape is loaded you get a tab with information about the tape. This is under 2012 R2 Server Veeam 7.0.0.839 HP LTO-5 in Tandberg Storage Loader.

For all versions of Veeam B&R: Additionally you may need to increase StorPort timeouts by creating a "StorPort" key with entries for all ...

May 13, 2014 · For all versions of Veeam B&R: Additionally you may need to increase StorPort timeouts by creating a "StorPort" key with entries for all tape devices. You can get DEVICEID & INSTANCE with the following PowerShell command: gwmi -class win32_tapedrive. Location: KLM\System\CurrentControlSet\Enum\SCSI\ DEVICEID \ INSTANCE \Device Parameters\StorPort\.

Feb 17, 2020 · This patch is a cumulative hotfix rollup for Veeam Backup & Replication Update 4b which also includes the following previously released hot fixes in the single package: Backup to Tape Jobs fail with “Tape Error: 1117” Potential data loss during Export Backup retention processing ; DOWNLOAD PATCH

Jul 31, 2019 · Backup (and other operations) to HPE LTO tape drives may constantly fail after installation of Veeam Backup & Replication 9.5 Update 4b (9.5.4.2866).Veeam fails to connect to the tape drive and re

21.10.2019 · Next step is the upgrade of the last 5 VBR-servers running VBR 9.5 U4 to VBR 9.5 U4b. Those VBR-servers have just a single tape drive (HPE LTO7) with forward forever incremental B2D-jobs and synthetic fulls with B2T-jobs. Regards, Didi7. Using the most recent Veeam B&R in 23 different environments now and counting!

24.08.2018 · I've tried to google the answer but nothing came up. I'm able to see the library, but no tapes are being recognized. I tried adding a different tape, restarting the tape server/veeam server, but nothing seems to work.

Apr 01, 2013 · Error code 1117 is generated by the Windows operating system and is always caused by I/O (Input / Output) throughput issues with either the disk or the controller that it is attached to. Check the disk for possible errors