srch

The IGMP snooping feature tracks which ports are attached to multicast-capable routers to help the routers forward IGMP membership reports. The IGMP snooping software responds to topology change notifications. By default, IGMP snooping is enabled on the device. Figure 5-1 shows an IGMP snooping switch that sits be tween the host and the IGMP ...

[edit] Setup (Updated) · In wireless, basic settings: enable "optimize multicast traffic" for all wireless radios, save and apply · In Setup, ...

May 07, 2015 · I am using a v24-sp2 K3 ARM 25648 build which has a igmp snooping option available under Setup > Networking for the br0 bridge. I have an IPTV decoder connected to the bridge as well as other computers in the same subnet, when I realized that my build allowed igmp snooping I enabled it to prevent the multicast traffic directed to the IPTV ...

10.10.2019 · Enabling igmp snooping in the switch of R7800 DD-WRT Forum Forum Index-> Atheros WiSOC based Hardware: Goto page Previous 1, 2. View previous topic:: View next topic . Author Message; Alozaros DD-WRT Guru Joined: 16 Nov 2015 Posts: 4466 Location: UK, London, just across the river.. ...

Aug 14, 2013 · Posted: Wed Aug 14, 2013 8:38 Post subject: IGMP Snooping/Proxy - YouView IPTV - Netgear Config: Hi all, I'm new poster to the forums, however have been here many times to find help for other issues i've had. I have done a fair bit of reading around this one but thought someone might able to help.

05.10.2019 · Enabling igmp snooping in the switch of R7800 DD-WRT Forum Forum Index-> Atheros WiSOC based Hardware: Goto page 1, 2 Next

04.06.2015 · DD-WRT Guru Joined: 13 Aug 2013 Posts: 6263 Location: Romerike, Norway: ... My intention was though to make use of the igmp snooping functionality to have all the devices in the same subnet and the igmp snooper keeping track of the port to which the IPTV decoder is attached by means of igmp control messages.

No. I want DD-WRT to either filter/drop/block or functionally-break all inbound, outbound, WAN and LAN multicast packets or at least reduce all ...

Setting up IPTV on a dd-wrt router is a pain in a ass. Last kernels support for nice feature called IGMP snooping, which do the same tricks as vlan & iptables does. But in much proper and easy way. Just need to upgrade to 2.6.34+ kernel.

IGMP snooping is used to find out on which ports there is an IGMP subscriber and only send IGMP traffic to that/those ports. For what reason ...

Setting up IPTV on a dd-wrt router is a pain in a ass. Last kernels support for nice feature called IGMP snooping, which do the same tricks as vlan & iptables does. But in much proper and easy way. Just need to upgrade to 2.6.34+ kernel.

igmp snooping not working? multicast flooding... Post new topic Reply to topic, DD-WRT Forum Forum Index -> Broadcom SoC based Hardware ...

on /Networking.asp page under bridging is igmp snooping on? ... 2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r47822 Std

The IPTV needs IGMP proxy and IGMP snooping to be enabled to work ... stock firmware is not reliable, so I decide to use DD-WRT instead.

Note: in AP mode, LAN cable to gateway/modem and LAN cable to IPTV box must be on the switch ports of the dd-wrt router and not on the WAN port, even if "assign WAN port to switch" is enabled. Tested on Linksys EA2700 (build 38581), Netgear R7000, Netgear R7000P. ARM Kong builds 35550M and 38580M. Do not consider these build recommendations.

26.09.2013 · Posted: Wed Aug 14, 2013 8:38 Post subject: IGMP Snooping/Proxy - YouView IPTV - Netgear Config: Hi all, I'm new poster to the forums, however have been here many times to find help for other issues i've had. I have done a fair bit of reading around this one but thought someone might able to help.

Dec 10, 2017 · Also tried enabling IGMP Snooping in the switch and caused IPv6 to stop working. I updated both R7800s to build 39000M and the same problem enabling IGMP Snooping in the switch caused IPv6 to stop working, I left it disabled. I did set up an Unbridged I/F eth1.15 and enabled IGMP Snooping on br0 under the Network (no boot loop like 38840M).

In Setup, networking, bridging, enable IGMP Snooping by selecting yes from the drop down ... the switch ports of the dd-wrt router and not on the WAN port, ...

This option enables "IGMP snooping" at the bridge level only. This will restrict the multicast flows to only one interface of the bridge (for ...

Setting up IPTV on a dd-wrt router is a pain in a ass. Last kernels support for nice feature called IGMP snooping, which do the same tricks as vlan ...

05.10.2019 · Also tried enabling IGMP Snooping in the switch and caused IPv6 to stop working. I updated both R7800s to build 39000M and the same problem enabling IGMP Snooping in the switch caused IPv6 to stop working, I left it disabled. I did set up an Unbridged I/F eth1.15 and enabled IGMP Snooping on br0 under the Network (no boot loop like 38840M).

Wriggerz DD-WRT Novice Joined: 14 Aug 2013. Posts: 5. Post Posted: Wed Aug 14, 2013 8:38 Post subject: IGMP Snooping/Proxy - YouView IPTV - Netgear Config ...