srch

26.01.2017 · Unicast/Multicast must be enabled. Default 10, range 1-64. When client joins and threshold is reached, conversion stops. Conversion resumes when count goes below threshold. Per multicast address: Snoop Timeout: Unicast/Multicast conversion must be enabled. 0-480, default 5 minutes. Per client. Per multicast group

Jan 26, 2017 · An added advantage of sending multicast packets as unicast is that unicast packets are acknowledged (ACK) and if no ACK is received, the packets are retried by the AP. Although converting multicast packets to unicast can use significantly less airtime and is more reliable, it is not recommended at a large scale.

So the device is sending the UDP messages, with a broadcast address as destination. A piece of software is listening for those UDP packets, and ...

Note: While there is an accepted answer now, it is only part; check the final iptables rule below. I'm receiving a unicast RTP stream on one interface and wish to send it out via multicast on a second interface. The system in question is an embedded processor running Linux, but I'm finding it equally difficult to set up on my Ubuntu 10.10 host.

When live video is being broadcasted over a LAN or WLAN network, it is possible to use two transmission methods: multicast streaming or unicast ...

24.02.2021 · Multicast Multicast transmission is a one-to-many broadcast methodology in which a WLAN AP forwards all broadcast packets from a multicast server source to a client subnet where multiple client devices are listening. The multicast server sends out a single stream during the transmission, allowing multiple clients to listen in.

when enabling multicast to unicast on the main wifi interface for qca, it should automatically be enabled for all wds stations too. on reboot or radio reinit, sometimes a station can be ath0.sta1 or ath0.sta5 etc, have to keep enabling it for each *.sta# interface that it comes online as.

Jun 12, 2006 · I'm pretty sure it does. 801.1x operates at the Data Link layer and multicasting occurs--IIRC--at the Network or Transport layers. One can prevent their router (using DD-WRT!) from allowing wireless clients to talk to each other, thus basically killing multicast at the direct level.

This section explains how to use the DD-WRT GUI to configure DD-WRT supporting multicast IPTV traffic while at the same time enable some LAN ports and Wireless Clients working in parallel. There are 2 ways to achieve this. The first is to unbridge the LAN area that shouldnt get flooded with mulicast packets.

when enabling multicast to unicast on the main wifi interface for qca, it should automatically be enabled for all wds stations too. on reboot or radio ...

To use wireless, I need that router. Is there a way (custom routing rules?) to put this multicast onto my local network and enjoy the HDTV?

what i used to do to get iptv working on ddwrt on build 35550M: ... enable multicast to unicast for both wireless interfaces

CTS Protection trigger 2; -default dd-wrt behavior A 802.11g client ... of buffered and/or multicast/broadcast data on the access point.

Major vendors like Ruckus, convert multicast to unicast to over wifi and currently is one of the best ... www.dd-wrt.com/phpBB2/viewtopic.php?t=87265&sid= ...

29.06.2015 · you can use the multicast-unicast , as the Multicast is used only when the client trying to discover the chromcast , but the rest of the communication will be unicast , if you don't have huge number of APs (in receptive to your network bandwidth) . then you can use multicast-unicast and you don't need to worry about it .

enable multicast to unicast for both wireless interfaces (thinking it replaces the older optimize multicast option); enable IGMP Snooping; reboot. Result is ...

This section explains how to use the DD-WRT GUI to configure DD-WRT supporting multicast IPTV traffic while at the same time enable some LAN ...

Multicast To Unicast. Available Settings: Enable, Disable Default Setting: Disable Recommended Setting: Disable Request that the AP will do multicast-to-unicast conversion for ARP, IPv4, and IPv6 frames. If enabled, such frames are to be sent to each station separately, with the DA replaced by their own MAC address rather than the group address.

when enabling multicast to unicast on the main wifi interface for qca, it should automatically be enabled for all wds stations too. on reboot or radio reinit, sometimes a station can be ath0.sta1 or ath0.sta5 etc, have to keep enabling it for each *.sta# interface that it comes online as.

Feb 24, 2021 · Multicast traffic is subject to packet loss that can cripple media quality, and unicast traffic can operate at higher data rates. Meraki APs will automatically perform a multicast-to-unicast packet conversion, ensuring high quality video transmission to a large number of clients.

Jun 16, 2014 · fl.berger. DD-WRT Novice. Joined: 16 Jun 2014. Posts: 1. Posted: Mon Jun 16, 2014 17:18 Post subject: UDP Multicast to Unicast-Convert. Hello everyone! I need some advice/help on a problem I'm facing. I do have a device that sends UDP-Broadcasts for a Discovery purpose. So the device is sending the UDP messages, with a broadcast address as ...

This section explains how to use the DD-WRT GUI to configure DD-WRT supporting multicast IPTV traffic while at the same time enable some LAN ports and Wireless Clients working in parallel. There are 2 ways to achieve this. The first is to unbridge the LAN area that shouldnt get flooded with mulicast packets. The second (and imho more elegand ...

Only use it when you're testing stuff from DD-WRT or using Mikrotik RouterOS. [edit] Multicast To Unicast. Available Settings: Enable ...