srch

CTS Protection trigger 1; - NON-default dd-wrt behavior A client that wants to use the radio channel to send data packet(s) of a size that is equal or above the defined RTS threshold value. CTS Protection trigger 2; -default dd-wrt behavior A 802.11g client attempts to connect to a SSID that is using channel bonding.

In wireless, basic settings: enable "optimize multicast traffic" for all wireless radios, ... the switch ports of the dd-wrt router and not on the WAN port, ...

Multicast Rate is usually an often talked about “advanced” router option that can seriously hinder your wireless use experience if you ...

Best settings to use. Hi all. I am new to DD-WRT and am trying to setup R8000. I have downloaded and flashed latest kong build released on 4 April 2016 using following steps. restore factory setting ->flash with kong build ->reset using hardware reset button ->configure router. Set up three SSIDs , all are named differently.

This is a Qualcomm Atheros technology to increase the throughput of ... messages for packets received in L2 multicast (which is required, ...

what i used to do to get iptv working on ddwrt on build 35550M: - enable optimize multicast traffic for both wireless interfaces

DD-Wrt also has an option to disable the SSID from being broadcast in beacon frames to reduce security issues. Supported rates. Each beacon carries information that describes the rates that the particular wireless LAN supports. For example, a beacon may indicate that only 1, 2, and 5.5Mbps data rates are available.

In wireless, basic settings: enable "optimize multicast traffic" for all wireless radios, save and apply · In Setup, networking, bridging, enable ...

http://www.dd-wrt.com/phpBB2/viewtopic.php?t=264152 ... Optimize Multicast Traffic - enabled TurboQAM - enabled

Install and Configure a DD-WRT Kong Router: DD-WRT is a wonderful open source custom router firmware that is supported on many devices. It adds features, stability and configurability to consumer routers.However, it's not easy for a novice starting out with DD-WRT.

3.3 Disable multicast traffic to reach the Wireless adapter ♦ ♦ 3.4 Setup an additional VLAN 3.5 Disable multicast traffic to reach the LAN Ports 1,2,3 ♦ 3.6 Enable DHCP for the additional local Networks and final steps ♦ • • 4 Block Multicast via Ebtables Firewall Introduction This section explains how to use the DD-WRT GUI to ...

3.3 Disable multicast traffic to reach the Wireless adapter ♦ ♦ 3.4 Setup an additional VLAN 3.5 Disable multicast traffic to reach the LAN Ports 1,2,3 ♦ 3.6 Enable DHCP for the additional local Networks and final steps ♦ • • 4 Block Multicast via Ebtables Firewall Introduction This section explains how to use the DD-WRT GUI to ...

Some wireless LAN applications may use multicast delivery of packets to and from wireless clients. For example, an application may stream ...

This section explains how to use the DD-WRT GUI to configure DD-WRT supporting multicast IPTV traffic while at the same time enable some LAN ports and Wireless Clients working in parallel. There are 2 ways to achieve this. The first is to unbridge the LAN area that shouldnt get flooded with mulicast packets. The second (and imho more elegand ...

-This speed-enhancing feature is available on all DD-WRT enabled G routers. It is hardware independent. Afterburner will only improve speeds when used with ...

Best settings to use. Hi all. I am new to DD-WRT and am trying to setup R8000. I have downloaded and flashed latest kong build released on 4 April 2016 using following steps. restore factory setting ->flash with kong build ->reset using hardware reset button ->configure router. Set up three SSIDs , all are named differently.

14.08.2019 · DD-WRT Guru Joined: 26 Nov 2010 Posts: 584: Posted: Sat May 11, 2019 6:42 Post subject: Multicast IPTV Causes Wireless TX errors on recent builds ...

Optimize Multicast Traffic – enabled ... DD-wrt exposes the middle frequencies under 149 and above 48 as selectable [per DFS preemption], ...

Sep 01, 2011 · I ended up with a two part solution, which involved upgrading my firmware to a later version, as well as unticking all the options EXCEPT filter multicast on the Security->Firewall page in dd-wrt admin, then saving, then disabling the SPI firewall within dd-wrt.

Hi <Kong>, Do you mean "Optimize Multicast Traffic" under Wireless settings could have an impact on the IGMP snooping feature of the Ethernet ...

This section explains how to use the DD-WRT GUI to configure DD-WRT supporting multicast IPTV traffic while at the same time enable some LAN ports and Wireless Clients working in parallel. There are 2 ways to achieve this. The first is to unbridge the LAN area that shouldnt get flooded with mulicast packets.