srch

22.04.2020 · Troubleshooting Internet Connectivity Use these steps if you can connect to your OpenWrt router's Web GUI, but cannot connect to the broader Internet (say, www.google.com): * Verify that the WAN connection of your router (usually Ethernet) is connected to your cable/DSL modem, or other device that's connected

Apr 02, 2020 · OpenWrt Debricking Guide When people say a router is bricked, this very generally means, that it does not function properly any longer and the reasons can be various. First of all, you should calm down, relax and read flash.layout, file systems in OpenWrt and bootloader CLI. Now depending on what exactly is broken, you have several possibilities:

Re: OpenWRT Router: One ethernet port does not work « Reply #18 on: November 12, 2019, 02:32:04 pm » If I disable the computer Ethernet port and re-enable it then the connection continues OK but if I physically unplug the cable from the computer and plug it in again then it breaks the connection.

If OpenWrt is configured as a router with default settings, you can access LuCI web interface and SSH command-line interface by domain name. If OpenWrt is configured as a network client, switch or access point, use its IP-address explicitly. You can utilize a network scanner or status page of your main router to find out OpenWrt IP-address.

This is copied from the OpenWRT Page concerning your router:. Wired stations cannot ping each other. This is a known bug: "switch eth0(Atheros AR8316) no traffic between ports possible" Based on the comments from the bug you can try these commands:

Can you verify that this connectivity problem exists between two computers connected at the same speed? I'm thinking that there might be a problem with the ...

02.01.2021 · root@OpenWrt:~# opkg list kmod-usb-net* # Install the Realtek module root@OpenWrt:~# opkg install kmod-usb-net-rtl8152 root@OpenWrt:~# reboot. but I don't understand where I'm wrong. there is something that still does …

13.11.2019 · In an earlier thread I flashed a router with OpenWRT so I now have a (TP-Link TL-WR841N/ND v9, Firmware Version OpenWrt Chaos Calmer 15.05.1 / LuCI 15.05-149) router running OpenWRT.For some unknown reason one of the four LAN ports (#1) does not work. I keep forgetting and each time I plug something there it takes me a while to realize the problem …

I'm wondering if OpenWRT supports dynamically connecting two wired EtherNET PHYs? What I would like to do is to have a device connect to ...

Hey guys, I'm new to OpenWRT and have just set it up on my Asus RT-AC51U. It seems like physical ethernet cable connections are not ...

I have problem with setting up OpenWrt as dhcp client. First router ASUS RT-N300 (with default firmware) is used to connect to internet. OpenWrt ...

Apr 22, 2020 · If the address ranges do not conflict, then ask on the OpenWrt Forum for more help. Change the LAN interface address, if necessary. To do this: From the Network → Interfaces page, click the Edit button next to the LAN interface. The “ IPv4 Address” field will show the LAN address found above. Enter a new address, that differs from the WAN ...

networkingopenwrtputtyrouterssh. I also posted on the OpenWRT forum about this issue. I'll copy the text of the problem verbatim, below, ...

1 / LuCI 15.05-149) router running OpenWRT. For some unknown reason one of the four LAN ports (#1) does not work. I keep forgetting and each ...

I have tried both OpenWRT and ROOter. However, I cannot get an internet connection on my PC! Everything seems to be ok. IP addresses and everything. By the way, I have tested the SIM card on a plug and play Huawei 4G router, working correctly. I have tried plugging the WG3526 into my main home router to get a internet. But, also not working.

I built from the latest BB version, it boots up fine. except the wired ethernet is not working. I can work on this if anyone can give me some pointer first. Thanks Chris [ 4.610000] bgmac bcma0:1: Found PHY addr: 30 (NOREGS) [ 4.620000] bgmac bcma0:1: Support for Roboswitch not implemented. All interfaces showing up though: