srch

Hi there, I have configured OpenWrt for the first time on my Linksys EA8300. I managed to setup my pppoe connection & get the wireless ...

From iwinfo phy0 is assigned to USB wifi and phy1 to internal radio (when I use other WiFi sticks internal radio is always phy0) It look like LUCI assume that radio0 is phy0 which is not true in that case. Output of uci show wireless: wireless.radio0=wifi-device. wireless.radio0.type=mac80211.

07.11.2010 · Ubiquiti UniFi AP and AP-LR Supported Versions NOTE for UAP-v2: As for July 2018, Ubiquiti seems to have blocked custom firmware installation possibility by using signatures on all 3.7 and later brand firmwares. As long as there is no brand pre-3.7 firmware available (in order to downgrade) for UAP-v2 devices, installing

Hi everyone, new to OpenWRT so I'm not sure if this is a dumb question ... config wifi-device 'radio0' option type 'mac80211' option channel ...

Hi! I have an issue with my Linksys WRT3200ACM (OpenWrt 21.02.1 r16325) : The radio0 never seem to be truly up, none of my device can ...

Hi radio0 Qualcomm Atheros QCA9880 802.11nac Channel: 36 (5.180 GHz) ... 1 rev 0 Firmware Version OpenWrt 19.07.3 r11063-85e04e9f46 / LuCI ...

Dec 16, 2019 · I’ve been tinkering with a Linksys router running OpenWRT, and noticed that by default, only the 2.4 GHz radio was active. It’s funny how much I’ve taken dual-band routers for granted, because the wireless was slow and unusable in that state.

Jan 17, 2022 · config wifi-iface 'wwan' option network 'wwan' option mode 'sta' option country 'US' option encryption 'psk2' option ssid 'myssid' option bssid 'xx:xx:xx:xx:xx:xx' option key 'mypassword' option device 'radio0'. and I added to the network config the section: config interface 'wwan' option proto 'dhcp'. the connection to the internet works fine ...

/etc/config/wireless ... config wifi-iface option device 'radio0' option mode 'ap' option ssid 'My-WiFi-Home' option network 'lan' option ...

16.12.2019 · Troubleshooting a disabled radio on an OpenWRT router I’ve been tinkering with a Linksys router running OpenWRT, and noticed that by default, only the 2.4 GHz radio was active.It’s funny how much I’ve taken dual-band routers for granted, because the wireless was slow and unusable in that state.

[Solved] C2600 kernel thinks 2.4GHz (radio0) is 5GHz on 19.07 Snapshot · Installing and Using OpenWrt Network and Wireless Configuration.

Nov 21, 2021 · Wi-Fi /etc/config/wireless See also: How do I enable Wi-Fi? The wireless radio UCI configuration is located in /etc/config/wireless. If the device has Ethernet ports, the wireless is turned OFF by default. Sections A typical wireless config file contains at least a pair of:

25.12.2021 · Linksys EA8300 [EA8300] The Linksys EA8300 is a MU-MIMO Tri-Band WiFi router, which has one 2.4GHz and two 5GHz WiFi Interfaces, making it an interesting choice for wireless backhaul or repeater applications. The radios support MCS 0-9 (up through 256 QAM) for devices and paths that are compatible with those high-density modulations.

17.01.2022 · the command that I called many times (speedtest-cli --json) exchange a lot of traffic with the internet so my first re-flexion is that i think for security purposes openwrt blocks access to radio0 I guess there's some option that I should set to my wifi-device 'radio0' section. Has someone an idea how I can fix this issue ?

From iwinfo phy0 is assigned to USB wifi and phy1 to internal radio (when I use other WiFi sticks internal radio is always phy0) It look like LUCI assume that radio0 is phy0 which is not true in that case. Output of uci show wireless: wireless.radio0=wifi-device. wireless.radio0.type=mac80211.

Enabling a Wi-Fi access point on OpenWrt Devices that have Ethernet ports have Wi-Fi turned off by default. This is a basic description of how to enable a Wi-Fi network and most importantly, how to properly configure your country code such that your Wi-Fi network complies with the legal regulations of your country.

01.07.2021 · FIXME This page is not fully translated, yet. Please help completing the translation. (remove this paragraph once the translation is finished) Wifi扩展器、中继器及桥接配置 If supported by both devices, consider using WDS, Layer 2 GRE tunnels

17.05.2014 · 1.缺省情况下，openwrt中的无线是关闭的，系统起来后，ifconfig和ifconfig -a, iwconfig均看不到wlan0接口原始的wireless配置文件如下：root@OpenWrt:/# cat /etc/config/wireless config wifi-device radio0 option type mac8

I am a new OpenWrt user with a basic knowlegde of networking. I need to configure a wireless router with a wireless wan and a wireless lan ...

Installing and Using OpenWrt ... (br-lan) Mon Feb 26 13:27:27 2018 daemon.notice netifd: radio0 (426): command failed: No error information ...

21.04.2018 · In May 2018, the OpenWrt forum suffered a total data loss. This archive is an effort to restore and make available as much content as possible. Content may be missing or not representing the latest edited version.

21.11.2021 · Wi-Fi /etc/config/wireless See also: How do I enable Wi-Fi? The wireless radio UCI configuration is located in /etc/config/wireless. If the device has Ethernet ports, the wireless is turned OFF by default. Sections A typical wireless config file contains at least a pair of:

For a router having two radios: radio0 - 2.4GHz radio1 - 5GHz Should ... the relation of client -> (preferred) interface somehow on OpenWrt?

Jan 15, 2020 · FS#2737 - Radio0 Device is not active. Freshly installed. Reboot/Restart do not fix the issue. Radio0 is a Generic 802.11bg device, which is always not active even after restart of the device, or reboot of the router. There is a Radio2, which is a Generic 802.11bgn device, which is working normally for 2.4Ghz band.

Jan 24, 2013 · The content of this topic has been archived on 21 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Software versions of OpenWrt/LEDE release, packages, etc. Luci-Network-Wireless, Radio0 Generic 802.11bg device is not active OpenWrt 19.03