Apr 22, 2016 · 1 Answer1. Show activity on this post. When you use static routing, you need to provide the next hop to the destination, and 1.1.1.35 can't be the next hop from your host, since your host is not on the same network as 1.1.1.35. You can't dictate a multihop path through a network from your host; you can only tell it the next hop to use, and the ...
Apr 04, 2016 · I'm trying to do route add -net 192.168.1.0 netmask 255.255.255.0 gw 10.8.0.6, in order to communicate with my NAS behind the Raspi, but it I get SIOCADDRT: Network is unreachable. These are the server side info: $ ifconfig -a
03.03.2014 · I can ping my router, my printer, and other machines inside the local network, but I can't ping anything in the outside net (also loopback ping on localhost says "host unreachable", but I'd say that it is NAT cancelling 127.0.0.1 requests) I can successfully connect through eth0, but I need to connect through wlan0. ifconfig output:
24.12.2006 · SIOCSARP: Network is unreachable arp: cannot set entry on line 1 of etherfile /etc/ethers ! diamond:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1
This answer is not useful. Show activity on this post. (Qouting) Whevener will add the default route need to specify a metric of 1 and execute the route add command: Execute the below command to add default route in HPUX: #route add default 192.168.178.1 1 add net default: gateway 192.168.178.1. Default route is added.
Dec 24, 2006 · SIOCSARP: Network is unreachable arp: cannot set entry on line 1 of etherfile /etc/ethers ! diamond:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1
Unable to add a static route: SIOADDRT: Network is unreachable. Ask Question Asked 7 years, 10 months ago. Active 6 months ago. Viewed 168k times 20 7. I've been bashing my head against a wall for a few days trying to figure this out: My ifconfig is: eth0 Link encap ...
May 13, 2002 · SIOCSARP: Network is unreachable What am I missing. Thanks 05-13-2002, 03:35 PM ... In your routing table u have only one network. Siddiqu.T Thread Tools: Search this ...
route add : network is unreachable ... My question is: What is the problem on the command? ... Going by that error message, you are using the wrong gateway address.
26.12.2017 · Connect: Network is unreachable. Wireshark shows that device cdev is sending messages. I edited /etc/host such that I left the first few lines unchanged as shown here. Code: 127.0.0.1 local host 127.0.1.1 esdev // I added the three lines below but not this comment 192.168.1.10 laptop 192.168.1.20 edev 192.168.1.43 cdev.
13.05.2002 · SIOCSARP: Network is unreachable What am I missing. Thanks 05-13-2002, 03:35 PM #2: siddiqu. Member . Registered: Mar 2001. Location: India. Posts: 332 Rep: Hi.. U can not put static MAC entry for other subnet. by default it will forward all the ...
Unable to add a static route: SIOADDRT: Network is unreachable · networking linux-networking route. I've been bashing my head against a wall for a few days ...
15.07.2012 · "Network is unreachable" errors while pinging. I double and triple checked all the settings – DNS and gateway were set up right. I even rebooted, but nothing worked. Then I vaguely remembered that I ran into the same issue a few years prior and also spent hours trying to figure out what was going wrong.
Apr 24 20:10:53 icecube bootpd[721]: ioctl SIOCSARP: Network is unreachable from the system doing the bootp... The back-end server bit is running on a RH ...
03.04.2016 · I'm trying to do route add -net 192.168.1.0 netmask 255.255.255.0 gw 10.8.0.6, in order to communicate with my NAS behind the Raspi, but it I get SIOCADDRT: Network is unreachable. These are the server side info: $ ifconfig -a
Dec 27, 2017 · Connect: Network is unreachable. Wireshark shows that device cdev is sending messages. I edited /etc/host such that I left the first few lines unchanged as shown here. Code: 127.0.0.1 local host 127.0.1.1 esdev // I added the three lines below but not this comment 192.168.1.10 laptop 192.168.1.20 edev 192.168.1.43 cdev.