srch

I have PrivateInternetAccess as my VPN provider installed on a LinkSys WRT32X with OpenWRT 19.07.5. The problem is that some pages don't ...

is there an issue around local /lan/ in openwrt and my receive outside openvpn domain in *.lan form ? My company domain Mycompany.lan. you are ...

15.08.2021 · OpenVPN startup and shutdown are slow, it can take up to 10 seconds to complete. If you want this VPN client connection to be started on boot and always active, click in the Enable checkbox of its line in the table. Note: If clicking on Start button in …

I have setup split tunneling using VPN Bypass to allow specific devices via ip to bypass the vpn. My goal is to have devices using the VPN to ...

Nov 03, 2018 · I am using OpenWrt Designated Driver 50061 My problem is quite simple. I HAVE to set external DNS for my network to work since my DNSMasq will only resolve local ips and refuse to forward requests to the configured dns forwarders So if I do "nslookup google.com 192.168.1.1" it fails with *** No internal type for both IPv4 and IPv6 Addresses (A+AAAA) records available for google.com Server ...

The best results can be achieved by using OpenVPN Connect v3 client software. When you use split-DNS, you will not see the DNS server that is being pushed in your ipconfig or ifconfig output. The DNS server will not get implemented at the network interface configuration level.

Unplug router from cable modem · Reboot router · Press & hold WPS button when light starts to blink (other light should blink very fast) · Set PC ...

01.01.2021 · So, if you want unbound to resolve dnsqueries through, openvpn have nothing to do here, it just need to be working, you need to make sure that: clients on lede client router when do a dns querie point to internal vpn ip where unbound is located, check doing nslookup and/or doing ifconfig/ipconfig on the clients

Hi, I'm not a network engineer but spent many years getting a OpenWRT OpenVPN server running at my home OpenWRT router to access from ...

Jan 24, 2015 · Not sure what you mean. This is initial beginning with the VPN so I have no history of DNS working through the VPN in the past. If you mean 'without the VPN being 'on,' then yes, it works fine connected to the "coffee house" public wifi (or anybody else's), and connected to home wifi.

I set up a openvpn server and it works, but there is no DNS possible. ... up DNS? :confused: It must be a problem with unbound because using …

Oct 14, 2019 · FS#2553 - dns name resolution with dnsmasq does not work after reboot. I’ve got a bunch of GL-MT300A devices suffering from this issue. They are configured as simple openvpn gateway behind a DSL router. There is no WIFI active, no WAN port, just a LAN interface and openvpn. Dnsmasq is used only for name resolution, and not for DHCP.

I'm running OpenWrt 21.02-SNAPSHOT on a Raspberry Pi 4b and after a clean install and setup I'm running into something I can't figure out ...

I've OpenWRT router with Backfire 10.03.1-rc3 (arch:brcm 2.6 kernel) I've set up an OpenVPN client connecting my router with workplace lan, and it works nicely, I can connect from router to networks (several) in workplace. My OpenVPN client uci-config looks like:

18.03.2016 · Not sure what you mean. This is initial beginning with the VPN so I have no history of DNS working through the VPN in the past. If you mean 'without the VPN being 'on,' then yes, it works fine connected to the "coffee house" public wifi (or …

Hi, I have set up rather ordinary OpenVPN configuration on my router (following the old OpenWRT manual). I use iPhone OpenVPN client (in TUN ...

That doesn't look like a standard openwrt release - is it just a custom theme, or is this a 3rd party version?

This means that *.openvpn.net will get resolved through the VPN DNS server, and the rest will resolve through the local DNS server 192.168.47.254. Note also that the VPN interface gets 3 IPv6 self-assigned DNS server addresses, which are not assigned by OpenVPN, but by the OS itself. This should not affect DNS resolution.

04.11.2018 · I am using OpenWrt Designated Driver 50061 My problem is quite simple. I HAVE to set external DNS for my network to work since my DNSMasq will only resolve local ips and refuse to forward requests to the configured dns forwarders So if I do "nslookup google.com 192.168.1.1" it fails with *** No internal type for both IPv4 and IPv6 Addresses (A+AAAA) …

I've setup my OpenWrt 18.06.2 snapshot machine as a travel router. It's meant to establish a VPN tunnel to my home gateway, ...