srch

Sounds like an issue with the UDM. The USG does not behave this way by default. My guess is bad default configuration. I don't know enough about the UDM to say, but surely if the UDM is handling DNS for names on the local network when WAN is up, there's no good reason I can think of why it couldn't do that when WAN is down. The big mystery is why this happens.

Create WAN Out rule assigning Resolver Group to the DNS Port Group STEP 4) Create Firewall Rule Dropping all traffic on the DNS Port Group Finally create a WAN Out Firewall Rule prohibiting all other DNS traffic on port 53. The Accept rule created in step 3 for our preferred resolvers will override. Key Settings: Type: WAN Out

The WAN DNS Server is what the USG itself will use to resolve DNS (if on Auto it should default to your ISP's DNS). This would include any ...

Log in to Ubiquiti UniFi controller. · Go to the Settings tab. · Navigate to Networks. · Click Edit Network > WAN. · Proceed to Common Settings > DNS Server and ...

The Problem

Step 2: Navigate to DNS Section. When you first log in, you will be created with a screen that shows you your devices. Select your device. Click on the Gear option, bottom left of the table of contents: This will drop you into a new panel. Navigate to Networks. You will make your changes in the WAN settings. Step 3: Update Network DNS

The WAN DNS Server is what the USG itself will use to resolve DNS (if on Auto it should default to your ISP's DNS). This would include any clients that are looking to the USG as a DNS server. The simplest way to set up Pihole is to point the WAN …

Oct 19, 2019 · More interesting is that this problem was brought about by some behind-the-scenes changes in how UniFi is managing DNS for the gateway device. Prior to this version of UniFi, the USG defaults to putting the WAN DNS value in /etc/resolv.conf. This is not ideal for two reasons: No DNS caching takes place for things running on the router itself. If you have IPS or load-balancing enabled this can result in an excessive number of DNS queries originating from the router, and creates a ton of noise ...

06.01.2019 · In this article we will look at how to apply DNS redirection on your Unifi network. Please note this is for IPv4 DNS requests. To catch and redirect IPv6 DNS requests, please check the corresponding article.. The goal is to catch and intercept DNS traffic that is NOT going through my carefully crafted infrastructure and force it to take my designed route.

You need to set the options in DHCP. The wan connection is what is looking to the outside. I don't have access to my unifi console right now for screen shots ...

Sort by: best. level 1. Amilmar. · 2y. You can configure DNS per WAN interface - this is what USG will use to resolve names. You can also configure DNS servers per network in it's DHCP configuration - this is what clients that getting addresses via DHCP will use. Or you can configure client itself as static and set DNS there.

Jan 06, 2019 · Achieving this with USG3. First, create a new firewall group containing the list of allowed DNS entries. Do this via the unifi-interface. Use the “Routing & Firewall” – “Firewall” – “Groups” menu options for this: Adding firewall address group. My group has 10 entries: 4x USG IP addresses, 1 per VLAN.

HOW TO UPDATE YOUR DNS For unifi and Streamyx customers - Please set your DNS at your router/modem/RG and any related device to auto-assign For TM subscribers other than unifi and Streamyx - Please set your DNS to: Primary: 202.188.18.188 Secondary: 1.9.1.9 Laptop/Desktop - Changing the DNS in TCP/IP setup Windows 7 1.

WAN DNS are set in Unifi Controller, NETWORK --> WAN -- COMMON setting. thats where you can overrulle your ISP DNS servers.

TP-Link Archer C1200 WAN settings / TP-Link. Tired of using TM default DNS server? Looking to speed up your Unifi Fibre internet speed?

I think the WAN > Preferred/Alternate DNS can be set for all UniFi devices so they can bypass the DNS servers listed in the Networks > DHCP Name Server. I left it blank on a switch and put a bad address in an AP as a test.

It is a mapping of an IP address to a domain name. This means that the ZyWall / USG / ATP / USG FLEX needs to be the DNS Server for the Clients. mceclip0.png.

The WAN DNS Server is what the USG itself will use to resolve DNS (if on Auto it should default to your ISP's DNS). This would include any clients that are looking to the USG as a DNS server. The simplest way to set up Pihole is to point the WAN DNS to the Pihole, leaving Lan DNS on Auto.

You will make your changes in the WAN settings. Step 3: Update Network DNS. Scroll to the Common Settings section of the page, and update the DNS Server options ...

Sort by: best. level 1. Amilmar. · 2y. You can configure DNS per WAN interface - this is what USG will use to resolve names. You can also configure DNS servers per network in it's DHCP configuration - this is what clients that getting addresses via DHCP will use. Or you can configure client itself as static and set DNS there.

Change WAN DNS Server. First, SSH into the router and enter in configuration mode with: configure. To stop the ISP DNS servers from populating /etc/resolv.

Default DNS server address for WAN connection for UDM Pro. Question. I have Verizon FiOS here in NJ. After I had finished setting up my WAN connection, I noticed my DNS server addresses were 1.1.1.1 and 8.8.8.8. Is this default setup for UDM Pro?

The Unifi Security Gateway (USG) can be setup to assign a custom DNS server. Supports 10/100/1000 Ethernet WAN connections. Click on Config.